PIC24FJ128GA110-I/PT Microchip Technology, PIC24FJ128GA110-I/PT Datasheet - Page 58

• Manufacturer Part Number: PIC24FJ128GA110-I/PT
• Description: IC PIC MCU FLASH 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ128GA110-I/PT

• Core Size: 16-Bit
• Program Memory Size: 128KB (43K x 24)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• Controller Family/series: PIC24
• No. Of I/o's: 85
• Ram Memory Size: 16KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDMA240015 - BOARD MCV PIM FOR 24F256GADM240011 - KIT STARTER MPLAB FOR PIC24F MCU
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC24FJ256GA110 FAMILY
REGISTER 5-1:
DS39905B-page 56
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13-10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
TRAPR
R/W-0
R/W-0
EXTR
2:
All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
TRAPR: Trap Reset Flag bit
1 = A Trap Conflict Reset has occurred
0 = A Trap Conflict Reset has not occurred
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an Address
0 = An illegal opcode or uninitialized W Reset has not occurred
Unimplemented: Read as ‘0’
CM: Configuration Word Mismatch Reset Flag bit
1 = A Configuration Word Mismatch Reset has occurred
0 = A Configuration Word Mismatch Reset has not occurred
VREGS: Voltage Regulator Standby Enable bit
1 = Regulator remains active during Sleep
0 = Regulator goes to standby during Sleep
EXTR: External Reset (MCLR) Pin bit
1 = A Master Clear (pin) Reset has occurred
0 = A Master Clear (pin) Reset has not occurred
SWR: Software Reset (Instruction) Flag bit
1 = A RESET instruction has been executed
0 = A RESET instruction has not been executed
SWDTEN: Software Enable/Disable of WDT bit
1 = WDT is enabled
0 = WDT is disabled
WDTO: Watchdog Timer Time-out Flag bit
1 = WDT time-out has occurred
0 = WDT time-out has not occurred
SLEEP: Wake From Sleep Flag bit
1 = Device has been in Sleep mode
0 = Device has not been in Sleep mode
IDLE: Wake-up From Idle Flag bit
1 = Device has been in Idle mode
0 = Device has not been in Idle mode
BOR: Brown-out Reset Flag bit
1 = A Brown-out Reset has occurred. Note that BOR is also set after a Power-on Reset.
0 = A Brown-out Reset has not occurred
POR: Power-on Reset Flag bit
1 = A Power-up Reset has occurred
0 = A Power-up Reset has not occurred
IOPUWR
R/W-0
R/W-0
SWR
Pointer caused a Reset
RCON: RESET CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
SWDTEN
R/W-0
U-0
—
(2)
WDTO
R/W-0
U-0
—
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SLEEP
(2)
R/W-0
U-0
—
(1)
R/W-0
IDLE
U-0
—
© 2008 Microchip Technology Inc.
x = Bit is unknown
R/W-0
R/W-1
BOR
CM
VREGS
R/W-0
R/W-1
POR
bit 8
bit 0