C8051F988-GM Silicon Laboratories Inc, C8051F988-GM Datasheet - Page 104

• Manufacturer Part Number: C8051F988-GM
• Description: IC MCU 8BIT 4KB FLASH 24QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F988-GM

• Program Memory Type: FLASH
• Program Memory Size: 4KB (4K x 8)
• Package / Case: 24-UQFN Exposed Pad, 24-HUQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Ram Size: 512 B
• Interface Type: I2C, SMBus, Enhanced UART, Enhanced SPI
• Maximum Clock Frequency: 7 KHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Operating Supply Voltage: 2.4 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F996DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• On-chip Dac: 10 bit, 4 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1959-5

C8051F99x-C8051F98x
8.12. CS0 Pin Monitor
The CS0 module provides accurate conversions in all operating modes of the CPU, peripherals and I/O
ports. Pin monitoring circuits are provided to improve interference immunity from high-current output pin
switching. The CS0 Pin Monitor register (CS0PM, SFR Definition 8.14) controls the operation of these pin
monitors.
Conversions in the CS0 module are immune to any change on digital inputs and immune to most output
switching. Even high-speed serial data transmission will not affect CS0 operation as long as the output
load is limited. Output changes that switch large loads such as LEDs and heavily-loaded communications
lines can affect conversion accuracy. For this reason, the CS0 module includes pin monitoring circuits that
will, if enabled, automatically adjust conversion timing if necessary to eliminate any effect from high-current
output pin switching.
The pin monitor enable bit should be set for any output signal that is expected to drive a large load.
Example: The SMBus in a system is heavily loaded with multiple slaves and a long PCB route. Set the
SMBus pin monitor enable, SMBPM = 1.
Example: Timer2 controls an LED on Port 1, pin 3 to provide variable dimming. Set the Port SFR write
monitor enable, PIOPM = 1.
Example: The SPI bus is used to communicate to a nearby host. The pin monitor is not needed because
the output is not heavily loaded, SPIPM remains = 0, the default reset state.
Pin monitors should not be enabled unless they are required. The pin monitor works by repeating any
portion of a conversion that may have been corrupted by a change on an output pin. Setting pin monitor
enables bits will slow CS0 conversions.
The frequency of CS0 retry operations can be limited by setting the CSPMMD bits. In the default (reset)
state, all converter retry requests will be performed. This is the recommended setting for all applications.
The number of retries per conversion can be limited to either two or four retries by changing CSPMMD.
Limiting the number of retries per conversion ensures that even in circumstances where extremely
frequent high-power output switching occurs, conversions will be completed, though there may be some
loss of accuracy due to switching noise.
Activity of the pin monitor circuit can be detected by reading the Pin Monitor Event bit, CS0PME, in register
CS0CN. This bit will be set if any CS0 converter retries have occurred. It remains set until cleared by
software or a device reset.
104
Rev. 1.0