MC908JB16DWE Freescale Semiconductor, MC908JB16DWE Datasheet - Page 287

• Manufacturer Part Number: MC908JB16DWE
• Description: IC MCU 16K FLASH 6MHZ USB 28SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JB16DWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 6MHz
• Connectivity: SCI, USB
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08JB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: I2C/SCI/SPI/USB
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE, KITUSBSPIDGLEVME, KITUSBSPIEVME, KIT33810EKEVME
• Minimum Operating Temperature: 0 C
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

15.9 IRQ Option Control Register
MC68HC908JB16
Freescale Semiconductor
—
Rev. 1.1
Address:
The IRQ option control register controls and monitors the external
interrupt function available on the PTE4 pin. It also disables/enables the
pullup resistor on the IRQ pin.
PTE4IF — PTE4 Interrupt Flag
PTE4IE — PTE4 Interrupt Enable
IRQPD — IRQ Pullup Disable
Reset:
Read:
Write:
•
•
•
This read-only status bit is high when a falling edge on PTE4 pin is
detected. PTE4IF bit clears when the IOCR is read.
This read/write bit enables or disables the interrupt function on the
PTE4 pin to trigger the IRQ interrupt. Setting the PTE4IE bit and
clearing the USBEN bit in the USB address register configure the
PTE4 pin for interrupt function to the IRQ interrupt. Setting PTE4IE
also enables the internal pullup on PTE4 pin.
This read/write bit controls the pullup option for the IRQ pin.
1 = Falling edge on PTE4 is detected and PTE4IE is set
0 = Falling edge on PTE4 is not detected or PTE4IE is clear
1 = PTE4 interrupt enabled; triggers IRQ interrupt
0 = PTE4 interrupt disabled
1 = Internal pullup is disconnected
0 = Internal pull-up is connected between IRQ pin and V
Controls pullup option on IRQ pin
Enables PTE4 pin for external interrupts to IRQ
Shows the state of the PTE4 interrupt flag
$001C
Bit 7
Figure 15-4. IRQ Option Control Register (IOCR)
0
0
External Interrupt (IRQ)
= Unimplemented
6
0
0
5
0
0
4
0
0
3
0
0
PTE4IF
2
0
External Interrupt (IRQ)
PTE4IE
1
0
Technical Data
DD
IRQPD
Bit 0
0
287