C8051F311-GM Silicon Laboratories Inc, C8051F311-GM Datasheet - Page 131

• Manufacturer Part Number: C8051F311-GM
• Description: IC 8051 MCU 16K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F31xr

Specifications of C8051F311-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F310DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 17 Channel
• No. Of I/o's: 25
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Package: 24QFN EP
• Device Core: 8051
• Family Name: C8051F31x
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1446 - ADAPTER PROGRAM TOOLSTICK F311336-1253 - DEV KIT FOR C8051F310/F311
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1254

13.1. Priority Crossbar Decoder
The Priority Crossbar Decoder (Figure 13.3) assigns a priority to each I/O function, starting at the top with
UART0. When a digital resource is selected, the least-significant unassigned Port pin is assigned to that
resource (excluding UART0, which is always at pins 4 and 5). If a Port pin is assigned, the Crossbar skips
that pin when assigning the next selected resource. Additionally, the Crossbar will skip Port pins whose
associated bits in the PnSKIP registers are set. The PnSKIP registers allow software to skip Port pins that
are to be used for analog input, dedicated functions, or GPIO.
Important Note on Crossbar Configuration: If a Port pin is claimed by a peripheral without use of the
Crossbar, its corresponding PnSKIP bit should be set. This applies to P0.0 if VREF is used, P0.3 and/or
P0.2 if the external oscillator circuit is enabled, P0.6 if the ADC is configured to use the external conversion
start signal (CNVSTR), and any selected ADC or Comparator inputs. The Crossbar skips selected pins as
if they were already assigned, and moves to the next unassigned pin. Figure 13.3 shows the Crossbar
Decoder priority with no Port pins skipped (P0SKIP, P1SKIP, P2SKIP = 0x00); Figure 13.4 shows the
Crossbar Decoder priority with the XTAL1 (P0.2) and XTAL2 (P0.3) pins skipped (P0SKIP = 0x0C to skip
P0.2 and P0.3 for XTAL use).
SF Signals
PIN I/O
TX0
RX0
SCK
MISO
MOSI
NSS*
SDA
SCL
CP0
CP0A
CP1
CP1A
SYSCLK
CEX0
CEX1
CEX2
CEX3
CEX4
ECI
T0
T1
SF Signals
*Note: NSS is only pinned out in 4-wire SPI mode.
Note: P1.6,P1.7,P2.6,P2.7 only available on the C8051F310/1/2/3/4/5; P1SKIP[7:6] should always be
set to 11b for the C8051F316/7 devices.
Port pin potentially available to peripheral
Special Function Signals are not assigned by the Crossbar. When these signals are enabled, the Crossbar must
be manually configured to skip their corresponding port pins.
Figure 13.3. Crossbar Priority Decoder with No Pins Skipped
0
0
1
0
2
0
P0SKIP[0:7]
3
0
P0
4
0
5
0
6
0
7
0
0
0
1
0
Rev. 1.7
2
0
P1SKIP[0:7]
3
0
P1
C8051F310/1/2/3/4/5/6/7
4
0
5
0
6
0
7
0
0
0
P2SKIP[0:3]
1
0
2
0
3
0
P2
4
5
6
7
131