MCF52213CAE50 Freescale Semiconductor, MCF52213CAE50 Datasheet - Page 27

• Manufacturer Part Number: MCF52213CAE50
• Description: IC MCU 32BIT 128K FLASH 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF5221xr

Specifications of MCF52213CAE50

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART, USB OTG
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: MCF522x
• Core: ColdFire V2
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, QSPI, UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 43
• Number Of Timers: 18
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: M52210DEMO, M52211EVB
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 8 Channel
• A/d Bit Size: 12 bit
• A/d Channels Available: 8
• Height: 1.4 mm
• Length: 10 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Width: 10 mm
• For Use With: M52210DEMO - BOARD DEV MCF5221X LOW COST
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Electrical Characteristics
2
This section contains electrical specification tables and reference timing diagrams for the microcontroller unit, including
detailed information on power considerations, DC/AC electrical characteristics, and AC timing specifications.
The electrical specifications are preliminary and are from previous designs or design simulations. These specifications may not
be fully tested or guaranteed at this early stage of the product life cycle. These specifications will, however, be met for
production silicon. Finalized specifications will be published after complete characterization and device qualifications have
been completed.
2.1
27
Electrical Characteristics
Maximum Ratings
1
2
3
4
5
6
Supply voltage
Clock synthesizer supply voltage
RAM standby supply voltage
USB standby supply voltage
Digital input voltage
EXTAL pin voltage
XTAL pin voltage
Instantaneous maximum current
Single pin limit (applies to all pins)
Operating temperature range (packaged)
Storage temperature range
Functional operating conditions are given in DC Electrical Specifications. Absolute Maximum Ratings
are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond
those listed may affect device reliability or cause permanent damage to the device.
This device contains circuitry protecting against damage due to high static voltage or electrical fields;
however, it is advised that normal precautions be taken to avoid application of any voltages higher
than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if
unused inputs are tied to an appropriate logic voltage level (V
Input must be current limited to the I
current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then
use the larger of the two values.
All functional non-supply pins are internally clamped to V
The power supply must maintain regulation within operating V
operating maximum current conditions. If positive injection current (V
injection current may flow out of V
regulation. Ensure that the external V
This is the greatest risk when the MCU is not consuming power (e.g., no clock).
Depending on the packaging; see the orderable part number summary.
The parameters specified in this data sheet supersede any values found in the module
specifications.
3
Rating
Table 19. Absolute Maximum Ratings
MCF52211 ColdFire Microcontroller, Rev. 2
4, 5
DD
DD
DD
and could result in the external power supply going out of
value specified. To determine the value of the required
load shunts current greater than maximum injection current.
NOTE
(T
Symbol
V
V
V
V
V
DDUSB
SS
DDPLL
L
V
EXTAL
T
STBY
V
I
XTAL
T
DD
DD
- T
stg
IN
A
and V
SS
H
DD
)
or V
range during instantaneous and
DD
in
.
DD
1, 2
> V
–0.3 to 4.0
–0.3 to 4.0
–0.3 to 4.0
–0.3 to 4.0
–40 to 85 or
+1.8 to 3.5
–65 to 150
).
0 to 70
0 to 3.3
0 to 3.3
Value
DD
25
) is greater than I
6
Freescale Semiconductor
Unit
mA
C
C
V
V
V
V
V
V
V
DD
, the