M30622SAFP#U5 Renesas Electronics America, M30622SAFP#U5 Datasheet - Page 488

• Manufacturer Part Number: M30622SAFP#U5
• Description: IC M16C MPU ROMLESS 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30622SAFP#U5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 50
• Program Memory Type: ROMless
• Ram Size: 3K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-QFP
• For Use With: 867-1000 - KIT QUICK START RENESAS 62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -

Multiple Interrupts
Table 2.14.1. Settings of interrupt priority levels
Figure 2.14.4. Hardware interrupts priorities
Reset > NMI > DBC > Watchdog timer > Peripheral I/O > Single step > Address match
Interrupt priority
level select bit
(5) Interrupt Priority
0
0
0
1
1
1
1
b2 b1 b0
0
The interrupt enable flag (I flag), the interrupt request bit, the interrupt priority select bit, and the IPL
are independent, and they are not affected by one another.
When either the IPL or the interrupt priority level is changed, the new level is reflected to the interrupt
in the following timing:
If there are two or more interrupt requests occurring at a point in time within a single sampling (check-
ing whether interrupt requests are made), the interrupt assigned a higher priority is accepted.
Assign an arbitrary priority to maskable interrupts (peripheral I/O interrupts) using the interrupt priority
level select bit. If the same interrupt priority level is assigned, however, the interrupt assigned a higher
hardware priority is accepted.
Priorities of the special interrupts, such as Reset (dealt with as an interrupt assigned the highest
priority), watchdog timer interrupt, etc. are regulated by hardware.
Figure 2.14.4 shows the priorities of hardware interrupts.
Software interrupts are not affected by the interrupt priority. If an instruction is executed, control
branches invariably to the interrupt routine.
0
0
1
0
0
1
1
1
• When changing the IPL using the REIT instruction, the reflection takes effect as of the instruction
• When changing the IPL using either the POPC, LDC or LDIPL instruction, the reflection takes
• When changing the interrupt priority level using the MOV or similar instruction, the reflection takes
0
1
0
0
1
0
1
1
that is executed in 2 clock cycles after the last clock cycle in volved in the REIT instruction.
effect as of the instruction that is executed in 3 cycles after the last clock cycle involved in the
instruction used.
effect as of the instruction that is executed in 2 clock cycles after the last clock cycle involved in
the instruction used.
_______
Level 0 (interrupt disabled)
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
________
Interrupt priority
level
Priority
order
High
Low
Table 2.14.2. Interrupt levels enabled according
IPL
0
0
0
1
1
1
1
0
2
IPL
IPL
0
0
1
0
0
1
1
1
1
IPL
0
1
0
0
1
0
1
1
0
to the contents of the IPL
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Interrupt levels 1 and above are enabled
All maskable interrupts are disabled
Interrupt levels 2 and above are enabled
Interrupt levels 3 and above are enabled
Interrupt levels 4 and above are enabled
Interrupt levels 5 and above are enabled
Interrupt levels 6 and above are enabled
Interrupt levels 7 and above are enabled
Enabled interrupt priority levels
M16C / 62A Group
Mitsubishi microcomputers
2-169