C8051F705-GM Silicon Laboratories Inc, C8051F705-GM Datasheet - Page 254

• Manufacturer Part Number: C8051F705-GM
• Description: IC 8051 MCU 15K FLASH 48-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F70xr

Specifications of C8051F705-GM

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Cap Sense, POR, PWM, WDT
• Number Of I /o: 39
• Program Memory Size: 15KB (15K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 32 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-QFN
• Processor Series: C8051F7x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 39
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F700DK
• Minimum Operating Temperature: - 40 C
• Height: 0.95 mm
• Length: 7 mm
• Supply Voltage (max): 1.9 V, 3.6 V
• Supply Voltage (min): 1.7 V, 1.8 V
• Width: 7 mm
• For Use With: 336-1635 - DEV KIT FOR C8051F700
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details
• Other names: 336-1612-5

C8051F70x/71x
32. UART0
UART0 is an asynchronous, full duplex serial port offering modes 1 and 3 of the standard 8051 UART.
Enhanced baud rate support allows a wide range of clock sources to generate standard baud rates (details
in Section “32.1. Enhanced Baud Rate Generation” on page 255). Received data buffering allows UART0
to start reception of a second incoming data byte before software has finished reading the previous data
byte.
UART0 has two associated SFRs: Serial Control Register 0 (SCON0) and Serial Data Buffer 0 (SBUF0).
The single SBUF0 location provides access to both transmit and receive registers. Writes to SBUF0
always access the Transmit register. Reads of SBUF0 always access the buffered Receive register;
it is not possible to read data from the Transmit register.
With UART0 interrupts enabled, an interrupt is generated each time a transmit is completed (TI0 is set in
SCON0), or a data byte has been received (RI0 is set in SCON0). The UART0 interrupt flags are not
cleared by hardware when the CPU vectors to the interrupt service routine. They must be cleared manually
by software, allowing software to determine the cause of the UART0 interrupt (transmit complete or receive
complete).
254
Rate Generator
UART Baud
Write to
SBUF
Figure 32.1. UART0 Block Diagram
Tx Clock
Rx Clock
Start
Start
Stop Bit
SBUF
Read
SCON
D
TB8
SET
CLR
Shift
Input Shift Register
Q
Shift
SFR Bus
(RX Latch)
(9 bits)
Tx Control
Rx Control
SBUF
0x1FF
SFR Bus
Zero Detector
(TX Shift)
SBUF
RB8
Rev. 1.0
Load SBUF
Rx IRQ
Tx IRQ
RI
TI
SBUF
Load
Send
Data
Interrupt
Serial
Port
TX
RX
Crossbar
Crossbar
Port I/O