C8051F347-GM Silicon Laboratories Inc, C8051F347-GM Datasheet - Page 133

• Manufacturer Part Number: C8051F347-GM
• Description: IC 8051 MCU 32K FLASH MEM 32-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F34xr

Specifications of C8051F347-GM

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 32-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 21x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2304 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-F34X, KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F340DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1748 - ADAPTER TOOLSTICK FOR C8051F34X770-1006 - ISP 4PORT FOR SILABS C8051F MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1348-5

14.2. Programmable Internal Low-Frequency (L-F) Oscillator
The C8051F340/1/2/3/4/5/8/9/C/D devices include a programmable internal oscillator which operates at a
nominal frequency of 80 kHz. The low-frequency oscillator circuit includes a divider that can be changed to
divide the clock by 1, 2, 4, or 8, using the OSCLD bits in the OSCLCN register (see SFR Definition 14.3).
Additionally, the OSCLF bits (OSCLCN5:2) can be used to adjust the oscillator’s output frequency.
14.2.1. Calibrating the Internal L-F Oscillator
Timers 2 and 3 include capture functions that can be used to capture the oscillator frequency, when run-
ning from a known time base. When either Timer 2 or Timer 3 is configured for L-F Oscillator Capture
Mode, a falling edge (Timer 2) or rising edge (Timer 3) of the low-frequency oscillator’s output will cause a
capture event on the corresponding timer. As a capture event occurs, the current timer value
(TMRnH:TMRnL) is copied into the timer reload registers (TMRnRLH:TMRnRLL). By recording the differ-
ence between two successive timer capture values, the low-frequency oscillator’s period can be calcu-
lated. The OSCLF bits can then be adjusted to produce the desired oscillator period.
Bits4–0: OSCCAL: Oscillator Calibration Value
Note: The contents of this register are undefined when Clock Recovery is enabled. See
“16.4. USB Clock Configuration” on page 166
R/W
Bit7
-
SFR Definition 14.2. OSCICL: Internal H-F Oscillator Calibration
These bits determine the internal H-F oscillator period. When set to 00000b, the oscillator
operates at its fastest setting. When set to 11111b, the oscillator operates at is slowest set-
ting. The contents of this register are factory calibrated to produce a 12 MHz internal oscilla-
tor frequency.
R/W
Bit6
-
R/W
Bit5
-
C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
R/W
Bit4
Rev. 1.3
R/W
for details on Clock Recovery.
Bit3
OSCCAL
R/W
Bit2
R/W
Bit1
R/W
Bit0
SFR Address:
Reset Value
Variable
Section
0xB3
133