C8051F347-GM Silicon Laboratories Inc, C8051F347-GM Datasheet - Page 150

• Manufacturer Part Number: C8051F347-GM
• Description: IC 8051 MCU 32K FLASH MEM 32-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F34xr

Specifications of C8051F347-GM

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 32-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 21x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2304 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-F34X, KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F340DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1748 - ADAPTER TOOLSTICK FOR C8051F34X770-1006 - ISP 4PORT FOR SILABS C8051F MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1348-5

C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
15.3. General Purpose Port I/O
Port pins that remain unassigned by the Crossbar and are not used by analog peripherals can be used for
general purpose I/O. Ports 3-0 are accessed through corresponding special function registers (SFRs) that
are both byte addressable and bit addressable. Port 4 (48-pin packages only) uses an SFR which is
byte-addressable. When writing to a Port, the value written to the SFR is latched to maintain the output
data value at each pin. When reading, the logic levels of the Port's input pins are returned regardless of the
XBRn settings (i.e., even when the pin is assigned to another signal by the Crossbar, the Port register can
always read its corresponding Port I/O pin). The exception to this is the execution of the read-modify-write
instructions. The read-modify-write instructions when operating on a Port SFR are the following: ANL,
ORL, XRL, JBC, CPL, INC, DEC, DJNZ and MOV, CLR or SETB, when the destination is an individual bit
in a Port SFR. For these instructions, the value of the register (not the pin) is read, modified, and written
back to the SFR.
150
Bits7–0: P0.[7:0]
Bits7–0: Analog Input Configuration Bits for P0.7–P0.0 (respectively).
P0.7
R/W
R/W
Bit7
Bit7
Write - Output appears on I/O pins per Crossbar Registers (when XBARE = ‘1’).
0: Logic Low Output.
1: Logic High Output (high impedance if corresponding P0MDOUT.n bit = 0).
Read - Always reads ‘0’ if selected as analog input in register P0MDIN. Directly reads Port
pin when configured as digital input.
0: P0.n pin is logic low.
1: P0.n pin is logic high.
Port pins configured as analog inputs have their weak pull-up, digital driver, and digital
receiver disabled.
0: Corresponding P0.n pin is configured as an analog input.
1: Corresponding P0.n pin is not configured as an analog input.
P0.6
R/W
R/W
Bit6
Bit6
SFR Definition 15.5. P0MDIN: Port0 Input Mode
P0.5
R/W
R/W
Bit5
Bit5
SFR Definition 15.4. P0: Port0 Latch
P0.4
R/W
R/W
Bit4
Bit4
Rev. 1.3
P0.3
R/W
R/W
Bit3
Bit3
P0.2
R/W
R/W
Bit2
Bit2
P0.1
R/W
R/W
Bit1
Bit1
(bit addressable)
P0.0
R/W
R/W
Bit0
Bit0
SFR Address:
SFR Address:
Reset Value
Reset Value
11111111
11111111
0xF1
0x80