M306N4FGGP#U3 Renesas Electronics America, M306N4FGGP#U3 Datasheet - Page 135

• Manufacturer Part Number: M306N4FGGP#U3
• Description: IC M16C/6N4 MCU FLASH 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N4FGGP#U3

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Family Name: M16C
• Maximum Speed: 24 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 87
• Interface Type: I2C/UART
• On-chip Adc: 26-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 11
• For Use With: R0K3306NKS001BE - KIT DEV RSK RSK-M16C/6NKR0K3306NKS000BE - KIT DEV RSK RSK-M16C/6NK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N4)
Rev.2.40
REJ09B0009-0240
Table 13.1 Timer Mode Specifications
Figure 13.7 Registers TA0MR to TA4MR in Timer Mode
Count source
Count operation
Divide ratio
Count start condition
Count stop condition
Interrupt request generation timing Timer underflow
TAiIN pin function
TAiOUT pin function
Read from timer
Write to timer
Select function
i = 0 to 4
13.1.1 Timer Mode
In timer mode, the timer counts a count source generated internally.
Table 13.1 lists the Timer Mode Specifications. Figure 13.7 shows Registers TA0MR to TA4MR in Timer Mode.
Apr 14, 2006
NOTES:
Timer Ai Mode Register (i = 0 to 4)
b7
1. The port direction bit for the TAiIN pin is set to 0 (input mode).
2. Selected by the PCLK0 bit in the PCLKR register.
Item
b6
0
b5
b4
b3
page 111 of 376
b2
0 0
b1
f1, f2, f8, f32, fC32
• Down-count
• When the timer underflows, it reloads the reload register contents and continues counting
1/(n+1)
Set the TAiS bit in the TABSR register to 1 (count starts)
Set the TAiS bit to 0 (count stops)
I/O port or gate input
I/O port or pulse output
Count value can be read by reading the TAi register
• When not counting and until the 1st count source is input after counting start
• When counting (after 1st count source input)
• Gate function
• Pulse output function
b0
Value written to the TAi register is written to both reload register and counter
Value written to the TAi register is written to only reload register
(Transferred to counter when reloaded next)
Counting can be started and stopped by an input signal to TAiIN pin
Whenever the timer underflows, the output polarity of TAiOUT pin is inverted.
When TAiS bit is set to 0 (count stops), the pin outputs a low.
Bit Symbol
TMOD0
TMOD1
TCK0
TCK1
MR0
MR1
MR2
MR3
TA0MR to TA4MR
Symbol
n: set value of the TAi register
Operating mode
select bits
Pulse output function
select bit
Gate function select bits
Set to 0 in timer mode
Count source select bits
Bit Name
0396h to 039Ah
Address
Specification
b7 b6
0 0 : Timer mode
0 : Pulse is not output
1 : Pulse is output
b4 b3
0 0 :
0 1 :
1 0 : Counts while input on the TAiIN pin
1 1 : Counts while input on the TAiIN pin
0 0 : f1 or f2
0 1 : f8
1 0 : f32
1 1 : fC32
b1 b0
(TAiOUT pin is a normal port pin)
(TAiOUT pin is a pulse output pin)
After Reset
}
is low
is high
Gate function not available
00h
(TAiIN pin functions as I/O port)
(1)
(1)
(2)
0000h to FFFFh
Function
RW
RW
RW
RW
RW
RW
RW
RW
RW
13. Timers