ATMEGA32HVB-8X3 Atmel, ATMEGA32HVB-8X3 Datasheet - Page 266

• Manufacturer Part Number: ATMEGA32HVB-8X3
• Description: MCU AVR 32KB FLASH 8MHZ 44TSSOP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32HVB-8X3

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI
• Peripherals: POR, WDT
• Number Of I /o: 17
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 25 V
• Data Converters: A/D 7x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TSSOP
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SPI, TWI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRSB200
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 7 Channel
• Package: 44TSSOP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 5|9|12|15|18|24 V
• For Use With: ATSTK524 - KIT STARTER ATMEGA32M1/MEGA32C1ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

38. Errata
38.1
38.1.1
38.1.2
38.2
38.2.1
38.2.2
8042B–AVR–06/10
ATmega16HVB
ATmega32HVB
Rev. B
Rev. A
Rev. B
Rev. A
Stack Pointer initial value
The stack pointer in ATmega16HVB is incorrectly initialized to 0x08ff instead of 0x04ff.
TWI bus can get stuck if TWI STOP condition bit is set in slave mode
If the TWSTO bit in TWCR is set while the TWI starts to receive data in slave mode, it can result
in pulling the SCL pin low and then the TWI bus will get stuck. To release the SCL pin and get
out of this situation the TWI module needs to be disabled and then re-enabled.
Not sampled.
No known errata.
Not sampled.
Problem Fix/Workaround
Initialize the stack pointer in software before the stack is used. Most C-compilers does initial-
ize the stack pointer without manual intervention.
Assembly Code Example:
ldi r16,high(RAMEND) ; Main program start out SPH,r16 ; Set Stack Pointer to top of RAM
ldi r16,low(RAMEND) out SPL,r16 C Code Example (if required): SP = RAMEND;
Problem Fix/Workaround
While in slave mode the TWSTO bit should be written only to recover from an error condition
and then cleared before a data transfer starts.
ATmega16HVB/32HVB
266