STM32F103C8T6TR STMicroelectronics, STM32F103C8T6TR Datasheet - Page 72

• Manufacturer Part Number: STM32F103C8T6TR
• Description: MCU ARM 64KB FLASH MEM 48-LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103C8T6TR

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32497-8511 - KIT STARTER FOR STM32 512K FLASH497-6438 - BOARD EVALUTION FOR STM32 512K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Electrical characteristics
72/96
Equation 1: R
The formula above
error below 1/4 of LSB. Here N = 12 (from 12-bit resolution).
Table 46.
1. Based on characterization, not tested in production.
Table 47.
1. ADC DC accuracy values are measured after internal calibration.
2. ADC Accuracy vs. Negative Injection Current: Injecting negative current on any of the standard (non-
3. Based on characterization, not tested in production.
1.5
7.5
13.5
28.5
41.5
55.5
71.5
239.5
Symbol
R
robust) analog input pins should be avoided as this significantly reduces the accuracy of the conversion
being performed on another analog input. It is recommended to add a Schottky diode (pin to ground) to
standard analog pins which may potentially inject negative current.
Any positive injection current within the limits specified for I
affect the ADC accuracy.
EO
EG
ED
ET
EL
AIN

------------------------------------------------------------- - R
f
T
ADC
Total unadjusted error
Offset error
Gain error
Differential linearity error
Integral linearity error
s
R
(cycles)
ADC accuracy - limited test conditions

AIN
AIN
C
(Equation
ADC
Parameter
max for f
max formula:
T
S

ln

1) is used to determine the maximum external impedance allowed for an
2
ADC
N
Doc ID 13587 Rev 12
+
0.11
0.54
0.96
2.04
2.96
3.96
5.11
17.1
2

= 14 MHz
–
f
f
V
T
Measurements made after
ADC calibration
ADC
PCLK2
ADC
A
DDA
= 25 °C
= 14 MHz, R
(1)
= 3 V to 3.6 V
t
S
= 56 MHz,
Test conditions
(µs)
INJ(PIN)
AIN
(1) (2)
and I
< 10 k,
STM32F103x8, STM32F103xB
INJ(PIN)
0.4
5.9
11.4
25.2
37.2
50
NA
NA
in
±1.3
±0.5
±0.7
±0.8
Typ
±1
Section 5.3.12
R
AIN
max (k)
Max
±1.5
±1.5
±1.5
±1
±2
(3)
does not
Unit
LSB