STM32F107VCT6 STMicroelectronics, STM32F107VCT6 Datasheet - Page 47

• Manufacturer Part Number: STM32F107VCT6
• Description: MCU ARM 256KB FLASH MEM 100-LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F107VCT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, Ethernet, I²C, IrDA, LIN, SPI, UART/USART, USB OTG
• Peripherals: DMA, POR, PWM, Voltage Detect, WDT
• Number Of I /o: 80
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: STM32F107x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: CAN, I2C, SPI, USART
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 80
• Number Of Timers: 10
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit x 2, 16 Channel
• On-chip Dac: 12 bit x 2, 2 Channel
• For Use With: 497-10591 - DAUGHTER BOARD FOR STM32497-10064 - EVAL BOARD497-9040 - DEV KIT FOR STM32497-9041 - DEV KIT FOR STM32497-9042 - DEV KIT FOR STM32497-9043 - DEV KIT FOR STM32497-8924 - EVAL BOARD FOR STM32F107VCT497-8853 - BOARD DEMO STM32 UNIV USB-UUSCI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-8913

STM32F105xx, STM32F107xx
Table 22.
1. Resonator characteristics given by the crystal/ceramic resonator manufacturer.
2. Based on characterization, not tested in production.
3. The relatively low value of the RF resistor offers a good protection against issues resulting from use in a
4. t
For C
5 pF to 25 pF range (typ.), designed for high-frequency applications, and selected to match
the requirements of the crystal or resonator (see
same size. The crystal manufacturer typically specifies a load capacitance which is the
series combination of C
can be used as a rough estimate of the combined pin and board capacitance) when sizing
C
microcontrollers” available from the ST website www.st.com.
Figure 16. Typical application with an 8 MHz crystal
1. R
Low-speed external clock generated from a crystal/ceramic resonator
The low-speed external (LSE) clock can be supplied with a 32.768 kHz crystal/ceramic
resonator oscillator. All the information given in this paragraph are based on characterization
results obtained with typical external components specified in
the resonator and the load capacitors have to be placed as close as possible to the oscillator
pins in order to minimize output distortion and startup stabilization time. Refer to the crystal
t
SU(HSE
Symbol
L1
f
OSC_IN
humid environment, due to the induced leakage and the bias condition change. However, it is
recommended to take this point into account if the MCU is used in tough humidity conditions.
oscillation is reached. This value is measured for a standard crystal resonator and it can vary significantly
with the crystal manufacturer
Resonator with
integrated capacitors
SU(HSE)
R
g
and C
C
EXT
i
2
m
F
L1
(4)
value depends on the crystal characteristics.
and C
is the startup time measured from the moment it is enabled (by software) to a stabilized 8 MHz
L2
Oscillator frequency
Feedback resistor
Recommended load capacitance
versus equivalent serial
resistance of the crystal (R
HSE driving current
Oscillator transconductance
Startup time
. Refer to the application note AN2867 “Oscillator design guide for ST
HSE 3-25 MHz oscillator characteristics
L2
C L2
, it is recommended to use high-quality external ceramic capacitors in the
C L1
Parameter
L1
8 MH z
resonator
R EXT (1)
and C
Doc ID 15274 Rev 5
L2
. PCB and MCU pin capacitance must be included (10 pF
OSC_OU T
OSC_IN
S
)
(3)
V
R F
DD
V
with 30 pF load
= 3.3 V, V
DD
Conditions
controlled
R
Figure
Startup
Bias
S
is stabilized
gain
= 30
(1) (2)
IN
16). C
= V
SS
STM32F10xxx
Table
L1
Electrical characteristics
and C
f HSE
Min
25
3
23. In the application,
L2
Typ
200
30
2
are usually the
Max
25
1
ai14128b
mA/V
47/101
MHz
Unit
mA
ms
k
pF