MC908GR4CDWE Freescale Semiconductor, MC908GR4CDWE Datasheet - Page 115

• Manufacturer Part Number: MC908GR4CDWE
• Description: IC MCU 4K FLASH 8MHZ 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR4CDWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 17
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 1
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8.2 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Examples of protect start address:
11.8 Wait Mode
Putting the MCU into wait mode while the FLASH is in read mode does not affect the operation of the
FLASH memory directly, but there will not be any memory activity since the CPU is inactive.
The WAIT instruction should not be executed while performing a program or erase operation on the
FLASH, otherwise the operation will discontinue, and the FLASH will be on Standby Mode.
11.9 STOP Mode
Putting the MCU into stop mode while the FLASH is in read mode does not affect the operation of the
FLASH memory directly, but there will not be any memory activity since the CPU is inactive.
The STOP instruction should not be executed while performing a program or erase operation on the
FLASH, otherwise the operation will discontinue, and the FLASH will be on Standby Mode
Freescale Semiconductor
The resultant 16-bit address is used for specifying the start address of the FLASH memory for block
protection. The FLASH is protected from this start address to the end of FLASH memory, at $FFFF.
With this mechanism, the protect start address can be $XX00, $XX40, $XX80, and $XXC0 (64 bytes
page boundaries) within the FLASH memory.
Note: The end address of the protected range is always $FFFF.
Standby Mode is the power saving mode of the FLASH module in which all
internal control signals to the FLASH are inactive and the current
consumption of the FLASH is at a minimum.
Start address of FLASH block protect
$FE (1111 1110)
$81 (1000 0001)
$82 (1000 0010)
BPR[7:0]
$80
$FF
Figure 11-4. FLASH Block Protect Start Address
Table 11-1. Examples of Protect Start Address
MC68HC908GR8 • MC68HC908GR4 Data Sheet, Rev. 7
1
1
The entire FLASH memory is not protected.
and so on...
The entire FLASH memory is protected.
NOTE
Start of Address of Protect Range
$E040 (1110 0000 0100 0000)
$E080 (1110 0000 1000 0000)
$FF80 (1111 1111 1000 0000)
FLBPR value
16-bit memory address
0 0 0 0 0 0
Wait Mode
115