PIC16LF819T-E/SO Microchip Technology, PIC16LF819T-E/SO Datasheet - Page 72

• Manufacturer Part Number: PIC16LF819T-E/SO
• Description: IC PIC MCU FLASH 2KX14 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16LF819T-E/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 18-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification

PIC18F2450/4450
5.5
The operation of program memory is unaffected by the
use of the extended instruction set.
Enabling the extended instruction set adds eight
additional two-word commands to the existing
PIC18 instruction set: ADDFSR, ADDULNK, CALLW,
MOVSF, MOVSS, PUSHL, SUBFSR and SUBULNK. These
instructions
Section 5.2.4 “Two-Word Instructions”.
5.6
Enabling the PIC18 extended instruction set (XINST
Configuration bit = 1) significantly changes certain
aspects
Specifically, the use of the Access Bank for many of the
core PIC18 instructions is different. This is due to the
introduction of a new addressing mode for the data
memory space. This mode also alters the behavior of
Indirect Addressing using FSR2 and its associated
operands.
What does not change is just as important. The size of
the data memory space is unchanged, as well as its
linear addressing. The SFR map remains the same.
Core PIC18 instructions can still operate in both Direct
and Indirect Addressing mode; inherent and literal
instructions do not change at all. Indirect Addressing
with FSR0 and FSR1 also remains unchanged.
5.6.1
Enabling the PIC18 extended instruction set changes
the behavior of Indirect Addressing using the FSR2
register pair and its associated file operands. Under the
proper conditions, instructions that use the Access
Bank – that is, most bit-oriented and byte-oriented
instructions – can invoke a form of Indexed Addressing
using an offset specified in the instruction. This special
addressing mode is known as Indexed Addressing with
Literal Offset or Indexed Literal Offset mode.
DS39760D-page 70
Program Memory and the
Extended Instruction Set
Data Memory and the Extended
Instruction Set
of
INDEXED ADDRESSING WITH
LITERAL OFFSET
data
are
executed
memory
and
as
its
described
addressing.
in
Literal Offset Addressing mode. This includes all byte-
unaffected.
When using the extended instruction set, this
addressing mode requires the following:
• The use of the Access Bank is forced (‘a’ = 0);
• The file address argument is less than or equal
Under these conditions, the file address of the
instruction is not interpreted as the lower byte of an
address (used with the BSR in Direct Addressing), or
as an 8-bit address in the Access Bank. Instead, the
value is interpreted as an offset value to an Address
Pointer specified by FSR2. The offset and the contents
of FSR2 are added to obtain the target address of the
operation.
5.6.2
Any of the core PIC18 instructions that can use Direct
Addressing are potentially affected by the Indexed
oriented and bit-oriented instructions, or almost one-half
of the standard PIC18 instruction set. Instructions that
only use Inherent or Literal Addressing modes are
Additionally, byte-oriented and bit-oriented instructions
are not affected if they do not use the Access Bank
(Access RAM bit is ‘1’) or include a file address of 60h
or above. Instructions meeting these criteria will
continue to execute as before. A comparison of the
different possible addressing modes when the
extended instruction set is enabled in shown in
Figure 5-8.
Those who desire to use byte-oriented or bit-oriented
instructions in the Indexed Literal Offset mode should
note the changes to assembler syntax for this mode.
This is described in more detail in Section 19.2.1
“Extended Instruction Syntax”.
and
to 5Fh.
INSTRUCTIONS AFFECTED BY
INDEXED LITERAL OFFSET MODE
© 2008 Microchip Technology Inc.