DSPIC30F5016-20I/PT Microchip Technology, DSPIC30F5016-20I/PT Datasheet - Page 14

• Manufacturer Part Number: DSPIC30F5016-20I/PT
• Description: IC DSPIC MCU/DSP 66K 80TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F5016-20I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 66KB (22K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• For Use With: AC164320 - MODULE SKT MPLAB PM3 80TQFPAC30F007 - MODULE SKT FOR DSPIC30F 80TQFP
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Other names: DSPIC30F501620IPT

dsPIC30F Family Reference Manual
22. Page 7-23, Section 7.17.3 Clock
23. Page 7-24, Section 7.17.7.2 Aborting a
24. Page 10-4, Section 10.3.6 Wake-up from
25. Page 10-4, Section 10.4 IDLE Mode
DS80169E-page 14
On page 7-23, Section 7.17.3 Clock Switching
Tips, add the following note to the end:
Switching Tips
Clock Switch
On page 7-24, Section 7.17.7.2 Aborting a Clock
Switch, should be replaced with the following:
7.17.7.2
The following code sequence would be used to ABORT an unsuccessful clock switch:
MOV
MOV.B
MOV.B
MOV.B
MOV.B
BCLR
SLEEP on Interrupt
On page 10-4, Section 10.3.6 Wake-up from
SLEEP on Interrupt, the following text should be
added:
User interrupt sources that are assigned to CPU
priority level 0 cannot wake the CPU from SLEEP
mode, because the interrupt source is effectively
disabled. To use an interrupt as a wake-up
source, the CPU priority level for the interrupt
must be assigned to CPU priority level 1 or
greater.
On page 10-4, Section 10.4 IDLE Mode, the
following text should be added:
User interrupt sources that are assigned to CPU
priority level 0 cannot wake the CPU from IDLE
mode, because the interrupt source is effectively
disabled. To use an interrupt as a wake-up
source, the CPU priority level for the interrupt
must be assigned to CPU priority level 1 or
greater.
#OSCCON,W1
#0x46,W2
#0x57,W3
W2, [W1]
W3, [W1]
OSCCON,#OSWEN
Aborting a Clock Switch
Note:
The application should not attempt to switch to a clock of frequency lower than
100 KHz when the fail-safe clock monitor is enabled. If such clock switching is
performed, the device may generate an oscillator fail trap and switch to the Fast RC
oscillator.
; pointer to OSCCON
; first unlock code
; second unlock code
; write first unlock code
; write second unlock code
; ABORT the switch
 2004 Microchip Technology Inc.