LPC2194JBD64,151 NXP Semiconductors, LPC2194JBD64,151 Datasheet - Page 24

• Manufacturer Part Number: LPC2194JBD64,151
• Description: IC ARM7 MCU FLASH 256K 64-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2100r

Specifications of LPC2194JBD64,151

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 60MHz
• Connectivity: CAN, I²C, Microwire, SPI, SSI, SSP, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 46
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 64-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: 568-1895; 935275729151; LPC2194JBD64-S

Philips Semiconductors
7. Limiting values
9397 750 12757
Preliminary data
6.21.3 RealMonitor™
RealMonitor is a configurable software module, developed by ARM Inc., which
enables real time debug. It is a lightweight debug monitor that runs in the background
while users debug their foreground application. It communicates with the host using
the DCC (Debug Communications Channel), which is present in the EmbeddedICE
logic. The LPC2194 contains a specific configuration of RealMonitor software
programmed into the on-chip Flash memory.
Table 9:
In accordance with the Absolute Maximum Rating System (IEC 60134).
[1]
[2]
[3]
[4]
[5]
[6]
Symbol Parameter
V
V
V
AV
V
V
I
I
T
P
stg
18
3
3A
i
i
IN
The following applies to the Limiting values:
a) Stresses above those listed under Limiting values may cause permanent damage to the device.
b) This product includes circuitry specifically designed for the protection of its internal devices from
c) Parameters are valid over operating temperature range unless otherwise specified. All voltages
Not to exceed 4.6 V.
Including voltage on outputs in 3-state mode.
Only valid when the V
The peak current is limited to 25 times the corresponding maximum current.
Dependent on package type.
This is a stress rating only and functional operation of the device at these or any conditions other
than those described in
of this specification is not implied.
the damaging effects of excessive static charge. Nonetheless, it is suggested that conventional
precautions be taken to avoid applying greater than the rated maximum.
are with respect to V
Supply voltage, internal rail
Supply voltage, external rail
Analog 3.3 V pad supply voltage
Analog input voltage on A/D related
pins
DC input voltage, 5 V tolerant I/O
pins
DC input voltage, other I/O pins
DC supply current per supply pin
DC ground current per ground pin
Storage temperature
Power dissipation (based on
package heat transfer, not device
power consumption)
Limiting values
[3][4]
Rev. 01 — 06 February 2004
3
supply voltage is present.
SS
unless otherwise noted.
Section 8 “Static characteristics”
[6]
[2][3]
[5]
[5]
Conditions
Single-chip 16/32-bit microcontrollers
and
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Section 9 “Dynamic characteristics”
Min
-
-
1.5
0.5
0.5
0.5
0.5
0.5
0.5
40
LPC2194
Max
+2.5
+3.6
4.6
5.1
6.0
V
100
100
125
-
3
+ 0.5 V
Unit
V
V
V
V
V
mA
mA
W
C
24 of 33