SAF-XC164CM-8F40F AA Infineon Technologies, SAF-XC164CM-8F40F AA Datasheet - Page 59
![IC MCU 16BIT FLASH TQFP-64-8](/photos/12/46/124653/saf-xc164cm-8f40f_aa_sml.jpg)
SAF-XC164CM-8F40F AA
Manufacturer Part Number
SAF-XC164CM-8F40F AA
Description
IC MCU 16BIT FLASH TQFP-64-8
Manufacturer
Infineon Technologies
Series
XC16xr
Datasheet
1.SAF-XC164CM-4F20F_AA.pdf
(70 pages)
Specifications of SAF-XC164CM-8F40F AA
Core Processor
C166SV2
Core Size
16-Bit
Speed
40MHz
Connectivity
CAN, SPI, UART/USART
Peripherals
PWM, WDT
Number Of I /o
47
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
6K x 8
Voltage - Supply (vcc/vdd)
2.35 V ~ 2.7 V
Data Converters
A/D 14x8/10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-LFQFP
Data Bus Width
16 bit
Data Ram Size
6 KB
Interface Type
2xASC, 2xSSC
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
47
Number Of Timers
9
Operating Supply Voltage
5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 14 Channel
Packages
PG-LQFP-64
Max Clock Frequency
40.0 MHz
Sram (incl. Cache)
6.0 KByte
Can Nodes
2
A / D Input Lines (incl. Fadc)
14
Program Memory
64.0 KByte
For Use With
B158-H8961-X-X-7600IN - KIT EASY XC164CMXC164CMUCANIN - KIT U-CAN STARTER XC164CMMCBX167-NET - BOARD EVAL INFINEON CAN/ETHRNTMCBXC167-BASIC - BOARD EVAL BASIC INFINEON XC16X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Other names
SAF-XC164CM-8F40FAACT
SAF-XC164CM-8F40FAACT
SAF-XC164CM-8F40FAAINCT
SAF-XC164CM-8F40FAACT
SAF-XC164CM-8F40FAAINCT
2)
3) The limit values for
4) This parameter includes the sample time
5) The actual duration of the reset calibration depends on the noise on the reference signal. Conversions
6) Not subject to production test - verified by design/characterization.
Figure 14
Data Sheet
V
cases will be X000
result register with the conversion result (
Values for the basic clock
When the post-calibration is switched off, the conversion time is reduced by 12 ×
executed during the reset calibration increase the calibration time. The TUE for those conversions may be
increased.
The given parameter values cover the complete operating range. Under relaxed operating conditions
(temperature, supply voltage) reduced values can be used for calculations. At room temperature and nominal
supply voltage the following typical values can be used:
C
AIN
AINTtyp
may exceed
V
= 12 pF,
AIN
Equivalent Circuitry for Analog Inputs
C
V
AINStyp
AGND
H
f
BC
or X3FF
R
must not be exceeded when selecting the peripheral frequency and the ADCTC setting.
or
Source
= 7 pF,
V
t
BC
AREF
H
, respectively.
depend on programming and can be taken from
up to the absolute maximum ratings. However, the conversion result in these
R
AINtyp
C
= 1.5 kΩ,
Ext
t
t
S
SYS
, the time for determining the digital result and the time to load the
= 1/
C
f
SYS
AREFTtyp
57
).
C
= 15 pF,
AINT
R
AIN, On
-
C
C
AINS
AREFStyp
= 13 pF,
A/D Converter
Table
Electrical Parameters
t
BC
.
15.
R
MCS05570
AREFtyp
C
AINS
Derivatives
V1.4, 2007-03
XC164CM
= 0.7 kΩ.