SAF-XC167CI-16F40F BB Infineon Technologies, SAF-XC167CI-16F40F BB Datasheet - Page 71

• Manufacturer Part Number: SAF-XC167CI-16F40F BB
• Description: IC MCU 16BIT 128KB TQFP-144-19
• Manufacturer: Infineon Technologies
• Series: XC16xr

Specifications of SAF-XC167CI-16F40F BB

• Core Processor: C166SV2
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: CAN, EBI/EMI, I²C, SPI, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 103
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.7 V
• Data Converters: A/D 16x8/10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LFQFP
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: 2xASC, 2xSSC, 1xI2C
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 103
• Number Of Timers: 11
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• Packages: PG-TQFP-144
• Max Clock Frequency: 40.0 MHz
• Sram (incl. Cache): 8.0 KByte
• Can Nodes: 2
• A / D Input Lines (incl. Fadc): 16
• Program Memory: 128.0 KByte
• For Use With: B158-H8963-X-X-7600IN - KIT EASY XC167CIMCBX167-NET - BOARD EVAL INFINEON CAN/ETHRNTMCBXC167-BASIC - BOARD EVAL BASIC INFINEON XC16X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: FX167CI16F40FBBNP; FX167CI16F40FBBXP; SAFXC167CI16F40FBBT; SP000094529; SP000224690

The specification of the external timing (AC Characteristics) depends on the period of the
CPU clock, called “TCP”.
The other peripherals are supplied with the system clock signal
frequency as the CPU clock signal
Bypass Operation
When bypass operation is configured (PLLCTRL = 0x
the internal oscillator (input clock signal XTAL1) through the input- and output-
prescalers:
f
If both divider factors are selected as ‘1’ (PLLIDIV = PLLODIV = ‘0’) the frequency of
directly follows the frequency of
cycle of the input clock
The lowest master clock frequency is achieved by selecting the maximum values for both
divider factors:
f
Phase Locked Loop (PLL)
When PLL operation is configured (PLLCTRL = 11
enabled and provides the master clock. The PLL multiplies the input frequency by the
factor F (
the output divider (F = PLLMUL+1 / (PLLIDIV+1 × PLLODIV+1)). The PLL circuit
synchronizes the master clock to the input clock. This synchronization is done smoothly,
i.e. the master clock frequency does not change abruptly.
Due to this adaptation to the input clock the frequency of
is locked to
of individual TCMs.
The timing listed in the AC Characteristics refers to TCPs. Because
f
circumstances.
The actual minimum value for TCP depends on the jitter of the PLL. As the PLL is
constantly adjusting its output frequency so it corresponds to the applied input frequency
(crystal or oscillator) the relative deviation for periods of more than one TCP is lower than
for one single TCP (see formula and
This is especially important for bus cycles using waitstates and e.g. for the operation of
timers, serial interfaces, etc. For all slower operations and longer periods (e.g. pulse train
generation or measurement, lower baudrates, etc.) the deviation caused by the PLL jitter
is negligible.
Data Sheet
MC
MC
MC
, the timing must be calculated using the minimum TCP possible under the respective
=
=
f
f
OSC
OSC
f
MC
/ ((PLLIDIV+1) × (PLLODIV+1)).
/ ((3 + 1) × (14 + 1)) =
f
OSC
=
f
OSC
. The slight variation causes a jitter of
× F) which results from the input divider, the multiplication factor, and
f
OSC
.
f
OSC
f
OSC
f
CPU
so the high and low time of
Figure
/ 60.
.
69
16).
B
) the on-chip phase locked loop is
B
f
MC
) the master clock is derived from
which also affects the duration
f
MC
is constantly adjusted so it
f
f
MC
SYS
Electrical Parameters
is defined by the duty
which has the same
f
CPU
XC167CI-16F
is derived from
Derivatives
V1.3, 2006-08
f
MC