XR17C158CV-F Exar Corporation, XR17C158CV-F Datasheet - Page 20

• Manufacturer Part Number: XR17C158CV-F
• Description: IC UART PCI BUS 5V OCTAL 144LQFP
• Manufacturer: Exar Corporation
• Type: Universal PCI Bus Octal UARTr

Specifications of XR17C158CV-F

• Number Of Channels: 8
• Package / Case: 144-LQFP
• Features: *
• Fifo's: 64 Byte
• Protocol: RS485
• Voltage - Supply: 5V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 6.25 Mbps
• Supply Voltage (max): 7 V
• Supply Current: 5 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 7 V
• No. Of Channels: 8
• Uart Features: High Performance, Read/Write Burst Operation
• Supply Voltage Range: -0.5V To 7V
• Operating Temperature Range: 0°C To +70°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1287

XR17C158
5V PCI BUS OCTAL UART
REGB [23:16] (default 0x00)
REGB register provides a control for simultaneous write to all 8 UARTs configuration register or individually.
This is very useful for device initialization during power-up and reset routines. Also, the register provides a
facility to interface to the non-volatile memory device such as a 93C46 EEPROM. In embedded applications,
the user can use this facility to store proprietary data.
The 158 provides 8 multi-purpose inputs/outputs [MPIO7:0] for general use. Each pin can be programmed to
be an input or output function. The input logic state can be set for normal or inverted level, and optionally set to
generate an interrupt. The outputs can be set to be normal logic 1 or 0 state, or 3-state. Their functions and
definitions are programmed through 5 registers: MPIOINT, MPIOLVL, MPIO3T, MPIOINV and MPIOSEL. If all
8 pins are set for inputs, all 8 interrupts would be OR’ed together. The OR’ed interrupt is reported in the
channel 0 UART interrupt status (3-bit interrupt encoding, bits [10:8], in the global interrupt status register).
SEE”THE INTERRUPT STATUS REGISTER” ON PAGE 15.
and to the 3-state condition for signal sharing.
Bit 7 represents MPIO7 pin and bit 0 represents MPIO0 pin. There are 5 registers that select, control and
monitor the 8 multipurpose inputs and outputs.
REGB[16](Read/Write)
REGB[19:17]
REGB[20] (Write-Only)
REGB[21] (Write-Only)
REGB[22] (Write-Only)
REGB[23] (Read-Only)
1.2.8
1.2.9
1.2.10
REGB Register
Multi-Purpose Inputs and Outputs
MPIO REGISTER
Logic 0 (default) write to each UART configuration registers individually.
Logic 1 enables simultaneous write to all 8 UARTs configuration register.
Reserved
Control the EECK, clock, output (pin 116) on the EEPROM interface.
Control the EECS, chips select, output (pin 115) to the EEPROM device.
EEDI (pin 114) data input. Write data to the EEPROM device.
EEDO (pin 113) data output. Read data from the EEPROM device.
Figure 6
20
shows the internal circuitry.
The pins may also be programmed to be outputs
xr
REV. 1.4.3