ADF7021-NBCPZ Analog Devices Inc, ADF7021-NBCPZ Datasheet - Page 32
![IC TXRX 80-650/842-916MHZ 48LFCS](/photos/6/50/65022/cp-48-8_sml.jpg)
ADF7021-NBCPZ
Manufacturer Part Number
ADF7021-NBCPZ
Description
IC TXRX 80-650/842-916MHZ 48LFCS
Manufacturer
Analog Devices Inc
Datasheet
1.ADF7021-NBCPZ-RL.pdf
(64 pages)
Specifications of ADF7021-NBCPZ
Frequency
80MHz ~ 650MHz, 842MHz ~ 916MHz
Data Rate - Maximum
33kbps
Modulation Or Protocol
2-FSK, 3-FSK, 4-FSK, MSK
Applications
Keyless Entery, Pagers, WMTS
Power - Output
-16dBm ~ 13dBm
Sensitivity
-130dBm
Voltage - Supply
2.3 V ~ 6 V
Current - Receiving
26mA
Current - Transmitting
32.3mA @ 10dBm
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
48-LFCSP
Receiving Current
26.4mA
Transmitting Current
20.2mA
Data Rate
24Kbps
Frequency Range
80MHz To 916MHz
Modulation Type
FSK, MSK
Rf Ic Case Style
LFCSP
No. Of Pins
48
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Product Depth (mm)
7mm
Product Length (mm)
7mm
Operating Supply Voltage (min)
2.3V
Operating Supply Voltage (typ)
2.5/3.3V
Operating Supply Voltage (max)
3.6V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
EVAL-ADF7021DBZ6 - BOARD EVAL ADF7021 608-614MHZEVAL-ADF7021DBZ5 - BOARD EVAL ADF7021EVAL-ADF7021DBZ3 - BOARD DAUGHTER FOR ADF7021EVAL-ADF7021DBZ2 - BOARD EVAL FOR ISM ADF7021
Memory Size
-
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ADF7021-NBCPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADF7021-NBCPZ-RL7
Manufacturer:
ST
Quantity:
210
ADF7021-N
DEMODULATION, DETECTION, AND CDR
System Overview
An overview of the demodulation, detection, and clock and
data recovery (CDR) of the received signal on the ADF7021-N
is shown in Figure 47.
The quadrature outputs of the IF filter are first limited and
then fed to either the correlator FSK demodulator or to the
linear FSK demodulator. The correlator demodulator is used
to demodulate 2FSK, 3FSK, and 4FSK. The linear demodulator
is used for frequency measurement and is enabled when the
AFC loop is active. The linear demodulator can also be used
to demodulate 2FSK.
Following the demodulator, a digital post demodulator filter
removes excess noise from the demodulator signal output.
Threshold/slicer detection is used for data recovery of 2FSK and
4FSK. Data recovery of 3FSK can be implemented using either
threshold detection or Viterbi detection.
An on-chip CDR PLL is used to resynchronize the received bit
stream to a local clock. It outputs the retimed data and clock on
the TxRxDATA and TxRxCLK pins, respectively.
TxRxDATA
TxRxCLK
LIMITERS
Figure 47. Overview of Demodulation, Detection, and CDR Process
Q
I
RECOVERY
CLOCK
DATA
AND
DEMODULATOR
CORRELATOR
FREQUENCY
LINEAR
MUX
MUX
THRESHOLD
DETECTION
DETECTION
2/3/4FSK
VITERBI
3FSK
Rev. 0 | Page 32 of 64
Correlator Demodulator
The correlator demodulator can be used for 2FSK, 3FSK, and
4FSK demodulation. Figure 48 shows the operation of the
correlator demodulator for 2FSK.
The quadrature outputs of the IF filter are first limited and then
fed to a digital frequency correlator that performs filtering and
frequency discrimination of the 2FSK/3FSK/4FSK spectrum.
For 2FSK modulation, data is recovered by comparing the
output levels from two correlators. The performance of this
frequency discriminator approximates that of a matched filter
detector, which is known to provide optimum detection in the
presence of additive white Gaussian noise (AWGN). This
method of FSK demodulation provides approximately 3 dB to
4 dB better sensitivity than a linear demodulator.
DISCRIMINATOR_BW
LIMITERS
Q
R4_DB(10:19)
I
Figure 48. 2FSK Correlator Demodulator Operation
FREQUENCY CORRELATOR
IF –
DISCRIM BW
f
DEV
DOT_PRODUCT
R4_DB7
IF
IF +
f
DEV
Rx_INVERT
R4_DB9
2FSK = +1, –1
OUTPUT LEVELS:
3FSK = +1, 0, –1
4FSK = +3, +1, –1, –3