ADF7021-NBCPZ Analog Devices Inc, ADF7021-NBCPZ Datasheet - Page 37
![IC TXRX 80-650/842-916MHZ 48LFCS](/photos/6/50/65022/cp-48-8_sml.jpg)
ADF7021-NBCPZ
Manufacturer Part Number
ADF7021-NBCPZ
Description
IC TXRX 80-650/842-916MHZ 48LFCS
Manufacturer
Analog Devices Inc
Datasheet
1.ADF7021-NBCPZ-RL.pdf
(64 pages)
Specifications of ADF7021-NBCPZ
Frequency
80MHz ~ 650MHz, 842MHz ~ 916MHz
Data Rate - Maximum
33kbps
Modulation Or Protocol
2-FSK, 3-FSK, 4-FSK, MSK
Applications
Keyless Entery, Pagers, WMTS
Power - Output
-16dBm ~ 13dBm
Sensitivity
-130dBm
Voltage - Supply
2.3 V ~ 6 V
Current - Receiving
26mA
Current - Transmitting
32.3mA @ 10dBm
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
48-LFCSP
Receiving Current
26.4mA
Transmitting Current
20.2mA
Data Rate
24Kbps
Frequency Range
80MHz To 916MHz
Modulation Type
FSK, MSK
Rf Ic Case Style
LFCSP
No. Of Pins
48
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Product Depth (mm)
7mm
Product Length (mm)
7mm
Operating Supply Voltage (min)
2.3V
Operating Supply Voltage (typ)
2.5/3.3V
Operating Supply Voltage (max)
3.6V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
EVAL-ADF7021DBZ6 - BOARD EVAL ADF7021 608-614MHZEVAL-ADF7021DBZ5 - BOARD EVAL ADF7021EVAL-ADF7021DBZ3 - BOARD DAUGHTER FOR ADF7021EVAL-ADF7021DBZ2 - BOARD EVAL FOR ISM ADF7021
Memory Size
-
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ADF7021-NBCPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADF7021-NBCPZ-RL7
Manufacturer:
ST
Quantity:
210
Internal AFC
The ADF7021-N supports a real-time, internal, automatic
frequency control loop. In this mode, an internal control loop
automatically monitors the frequency error and adjusts the
synthesizer-N divider using an internal proportional integral
(PI) control loop.
The internal AFC control loop parameters are controlled in
Register 10. The internal AFC loop is activated by setting
R10_DB4 to 1. A scaling coefficient must also be entered, based
on the crystal frequency in use. This is set up in R10_DB[5:16]
and should be calculated using
Maximum AFC Range
The maximum frequency correction range of the AFC loop is
programmable on the ADF7021-N. This is set by R10_DB[24:31].
The maximum AFC correction range is the difference in
frequency between the upper and lower limits of the AFC
tuning range. For example, if the maximum AFC correction
range is set to 10 kHz, the AFC can adjust the receiver LO
within the f
However, when RF_DIVIDE_BY_2 (R1_DB18) is enabled, the
programmed range is halved. The user should account for this
halving by doubling the programmed maximum AFC range.
The recommended maximum AFC correction range should be
≤1.5 × IF filter bandwidth. If the maximum frequency correction
range is set to be >1.5 × IF filter bandwidth, the attenuation of
the IF filter can degrade the AFC loop sensitivity.
The adjacent channel rejection (ACR) performance of the
receivers can be degraded when AFC is enabled and the AFC
correction range is close to the IF filter bandwidth. However,
because the AFC correction range is programmable, the user
can trade off correction range and ACR performance.
AFC
_
LO
SCALING
± 5 kHz range.
_
FACTOR
=
Round
⎛
⎜
⎜
⎝
2
24
XTAL
×
500
⎞
⎟
⎟
⎠
Rev. 0 | Page 37 of 64
When AFC errors are removed using either the internal or
external AFC, further improvement in receiver sensitivity can
be obtained by reducing the IF filter bandwidth using the
IF_FILTER_BW bits (R4_DB[30:31]).
AUTOMATIC SYNC WORD DETECTION (SWD)
The ADF7021-N also supports automatic detection of the sync
or ID fields. To activate this mode, the sync (or ID) word must
be preprogrammed into the ADF7021-N. In receive mode, this
preprogrammed word is compared to the received bit stream.
When a valid match is identified, the external SWD pin is
asserted by the ADF7021-N on the next Rx clock pulse.
This feature can be used to alert the microprocessor that a
valid channel has been detected. It relaxes the computational
requirements of the microprocessor and reduces the overall
power consumption.
The SWD signal can also be used to frame the received packet
by staying high for a preprogrammed number of bytes. The data
packet length can be set in R12_DB[8:15].
The SWD pin status can be configured by setting R12_DB[6:7].
R11_DB[4:5] are used to set the length of the sync/ID word, which
can be 12, 16, 20, or 24 bits long. A value of 24 bits is recommended
to minimize false sync word detection in the receiver that can
occur during recovery of the remainder of the packet or when a
noise/no signal is present at the receiver input. The transmitter
must transmit the sync byte MSB first and the LSB last to ensure
proper alignment in the receiver sync-byte-detection hardware.
An error tolerance parameter can also be programmed that
accepts a valid match when up to three bits of the word are
incorrect. The error tolerance value is assigned in R11_DB[6:7].
ADF7021-N