MFRC53101T/0FE,112 NXP Semiconductors, MFRC53101T/0FE,112 Datasheet - Page 20

• Manufacturer Part Number: MFRC53101T/0FE,112
• Description: IC MIFARE HS READER 32-SOIC
• Manufacturer: NXP Semiconductors
• Series: MIFARE®r

Specifications of MFRC53101T/0FE,112

• Rf Type: Read Only
• Frequency: 13.56MHz
• Features: ISO14443-A, ISO14443-B, ISO15693
• Package / Case: 32-SOIC (0.300", 7.50mm Width)
• Product: RFID Readers
• Operating Temperature Range: - 25 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-2224-5; 935269691112; MFRC531; MFRC53101TD

NXP Semiconductors
Table 20.
MFRC531_34
Product data sheet
PUBLIC
Register
InterruptEn
InterruptRq
Interrupt control registers
9.4.2.1 Controlling interrupts and getting their status
9.4.2.2 Accessing the interrupt registers
9.4.2 Interrupt request handling
Bit 7
SetIEn
SetIRq
Table 19.
The MFRC531 informs the microprocessor about the interrupt request source by setting
the relevant bit in the InterruptRq register. The relevance of each interrupt request bit as
source for an interrupt can be masked by the InterruptEn register interrupt enable bits.
If any interrupt request flag is set to logic 1 (showing that an interrupt request is pending)
and the corresponding interrupt enable flag is set, the PrimaryStatus register IRq flag bit is
set to logic 1. Different interrupt sources can activate simultaneously because all interrupt
request bits are OR’ed, coupled to the IRq flag and then forwarded to pin IRQ.
The interrupt request bits are automatically set by the MFRC531’s internal state
machines. In addition, the microprocessor can also set or clear the interrupt request bits
as required.
A special implementation of the InterruptRq and InterruptEn registers enables changing
an individual bit status without influencing any other bits. If an interrupt register is set to
logic 1, bit SetIxx and the specific bit must both be set to logic 1 at the same time. If a
specific interrupt flag is cleared, zero must be written to the SetIxx and the interrupt
register address must be set to logic 1 at the same time.
If a content bit is not changed during the setting or clearing phase, zero must be written to
the specific bit location.
Example: Writing 3Fh to the InterruptRq register clears all bits. SetIRq is set to logic 0
while all other bits are set to logic 1. Writing 81h to the InterruptRq register sets LoAlertIRq
to logic 1 and leaves all other bits unchanged.
Interrupt flag
TimerIRq
TxIRq
RxIRq
IdleIRq
HiAlertIRq
LoAlertIRq
Bit 6
reserved
reserved
Interrupt sources
receiver
Interrupt source
timer unit
transmitter
CRC coprocessor
EEPROM
Command register
FIFO buffer
FIFO buffer
TimerIRq
Bit 5
TimerIEn
Rev. 3.4 — 26 January 2010
056634
Bit 4
TxIEn
TxIRq
RxIRq
Bit 3
RxIEn
Trigger action
timer counts from 1 to 0
a data stream, transmitted to the card, ends
all data from the FIFO buffer has been processed
all data from the FIFO buffer has been
programmed
a data stream, received from the card, ends
command execution finishes
FIFO buffer is full
FIFO buffer is empty
Bit 2
IdleIEn
IdleIRq
ISO/IEC 14443 reader IC
Bit 1
HiAlertIEn
HiAlertIRq
MFRC531
© NXP B.V. 2010. All rights reserved.
Bit 0
LoAlertIEn
LoAlertIRq
20 of 116