PIC18F2320-E/SO Microchip Technology, PIC18F2320-E/SO Datasheet - Page 84

• Manufacturer Part Number: PIC18F2320-E/SO
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SOP,28PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2320-E/SO

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F2220/2320/4220/4320
REGISTER 7-1:
DS39599G-page 82
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
EEPGD
R/W-x
When a WRERR occurs, the EEPGD or FREE bits are not cleared. This allows tracing of the error
condition.
EEPGD: Flash Program or Data EEPROM Memory Select bit
1 = Access Flash program memory
0 = Access data EEPROM memory
CFGS: Flash Program/Data EEPROM or Configuration Select bit
1 = Access Configuration or Calibration registers
0 = Access Flash program or data EEPROM memory
Unimplemented: Read as ‘0’
FREE: Flash Row Erase Enable bit
1 = Erase the program memory row addressed by TBLPTR on the next WR command (cleared by
0 = Perform write-only
WRERR: EEPROM Error Flag bit
1 = A write operation was prematurely terminated (MCLR or WDT Reset during self-timed erase or
0 = The write operation completed normally
WREN: Erase/Write Enable bit
1 = Allows write cycles
0 = Inhibits write cycles
WR: Write Control bit
1 = Initiates a data EEPROM erase/write cycle or a program memory erase cycle or write cycle
0 = Write cycle is completed
RD: Read Control bit
1 = Initiates a memory read (Read takes one cycle. RD is cleared in hardware. The RD bit can only be
0 = Read completed
R/W-x
CFGS
completion of erase operation)
program operation)
(The operation is self-timed and the bit is cleared by hardware once write is complete.
The WR bit can only be set (not cleared) in software.)
set (not cleared) in software. RD bit cannot be set when EEPGD = 1.)
EECON1: DATA EEPROM CONTROL REGISTER 1
S = Settable bit
W = Writable bit
‘1’ = Bit is set
U-0
—
R/W-0
FREE
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
WRERR
R/W-x
(1)
WREN
R/W-0
© 2007 Microchip Technology Inc.
x = Bit is unknown
R/S-0
WR
R/S-0
RD
bit 0