PIC18F4585-E/ML Microchip Technology, PIC18F4585-E/ML Datasheet - Page 134

• Manufacturer Part Number: PIC18F4585-E/ML
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,LLCC,44PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4585-E/ML

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 48KB (24K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.25K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 44-QFN
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.25 KB
• Interface Type: I2C, SPI, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 44
• Number Of Timers: 1 x 8
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11 bit
• Height: 0.88 mm
• Length: 8 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 8 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3-DB18F4680 - BOARD DAUGHTER ICEPIC3
• Lead Free Status / Rohs Status: Details

PIC18F2585/2680/4585/4680
10.2
PORTB is an 8-bit wide, bidirectional port. The
corresponding data direction register is TRISB. Setting
a TRISB bit (= 1) will make the corresponding PORTB
pin an input (i.e., put the corresponding output driver in
a high-impedance mode). Clearing a TRISB bit (= 0)
will make the corresponding PORTB pin an output (i.e.,
put the contents of the output latch on the selected pin).
The Data Latch register (LATB) is also memory
mapped. Read-modify-write operations on the LATB
register read and write the latched output value for
PORTB.
Pins RB2 through RB3 are multiplexed with the ECAN
peripheral. Refer to Section 23.0 “ECAN™ Technol-
ogy” for proper settings of TRISB when CAN is
enabled.
EXAMPLE 10-2:
Each of the PORTB pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is
performed by clearing bit RBPU (INTCON2<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on all device Resets.
DS39625C-page 132
CLRF
CLRF
MOVLW
MOVWF
MOVLW
MOVWF
Note:
PORTB, TRISB and LATB
Registers
PORTB
LATB
0Eh
ADCON1 ; digital I/O pins
0CFh
TRISB
On a Power-on Reset, RB4:RB0 are
configured as analog inputs by default and
read as ‘0’; RB7:RB5 are configured as
digital inputs.
By programming the Configuration bit,
PBADEN (CONFIG3H<1>), RB4:RB0 will
alternatively be configured as digital inputs
on POR.
; Initialize PORTB by
; clearing output
; data latches
; Alternate method
; to clear output
; data latches
; Set RB<4:0> as
; (required if config bit
; PBADEN is set)
; Value used to
; initialize data
; direction
; Set RB<3:0> as inputs
; RB<5:4> as outputs
; RB<7:6> as inputs
INITIALIZING PORTB
Preliminary
Four of the PORTB pins (RB7:RB4) have an interrupt-
on-change feature. Only pins configured as inputs can
cause this interrupt to occur (i.e., any RB7:RB4 pin
configured as an output is excluded from the interrupt-
on-change comparison). The input pins (of RB7:RB4)
are compared with the old value latched on the last
read of PORTB. The “mismatch” outputs of RB7:RB4
are ORed together to generate the RB Port Change
Interrupt with Flag bit, RBIF (INTCON<0>).
This interrupt can wake the device from Sleep. The
user, in the Interrupt Service Routine, can clear the
interrupt in the following manner:
a)
b)
A mismatch condition will continue to set flag bit RBIF.
Reading PORTB will end the mismatch condition and
allow flag bit RBIF to be cleared.
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt-on-change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
Any read or write of PORTB (except with the
MOVFF (ANY), PORTB instruction). This will
end the mismatch condition.
Clear flag bit RBIF.
© 2007 Microchip Technology Inc.