PIC18F4585-E/ML Microchip Technology, PIC18F4585-E/ML Datasheet - Page 44

• Manufacturer Part Number: PIC18F4585-E/ML
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,LLCC,44PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4585-E/ML

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 48KB (24K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.25K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 44-QFN
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.25 KB
• Interface Type: I2C, SPI, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 44
• Number Of Timers: 1 x 8
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11 bit
• Height: 0.88 mm
• Length: 8 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 8 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3-DB18F4680 - BOARD DAUGHTER ICEPIC3
• Lead Free Status / Rohs Status: Details

PIC18F2585/2680/4585/4680
REGISTER 4-1:
DS39625C-page 42
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
RCON: RESET CONTROL REGISTER
bit 7
IPEN: Interrupt Priority Enable bit
1 = Enable priority levels on interrupts
0 = Disable priority levels on interrupts (16CXXX Compatibility mode)
SBOREN: BOR Software Enable bit
If BOREN1:BOREN0 = 01:
1 = BOR is enabled
0 = BOR is disabled
If BOREN1:BOREN0 = 00, 10 or 11:
Bit is disabled and read as ‘0’.
Unimplemented: Read as ‘0’
RI: RESET Instruction Flag bit
1 = The RESET instruction was not executed (set by firmware only)
0 = The RESET instruction was executed causing a device Reset (must be set in software after
TO: Watchdog Time-out Flag bit
1 = Set by power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-down Detection Flag bit
1 = Set by power-up or by the CLRWDT instruction
0 = Set by execution of the SLEEP instruction
POR: Power-on Reset Status bit
1 = A Power-on Reset has not occurred (set by firmware only)
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
BOR: Brown-out Reset Status bit
1 = A Brown-out Reset has not occurred (set by firmware only)
0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)
Legend:
R = Readable bit
-n = Value at POR
R/W-0
Note 1: If SBOREN is enabled, its Reset state is ‘1’; otherwise, it is ‘0’.
Note 1: It is recommended that the POR bit be set after a Power-on Reset has been
IPEN
a Brown-out Reset occurs)
2: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming
2: The actual Reset value of POR is determined by the type of device Reset. See the
detected so that subsequent Power-on Resets may be detected.
that POR was set to ‘1’ by software immediately after POR).
notes following this register and Section 4.6 “Reset State of Registers” for
additional information.
SBOREN
R/W-1
(1)
U-0
Preliminary
—
W = Writable bit
‘1’ = Bit is set
(2)
(1)
R/W-1
RI
R-1
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
TO
R-1
PD
© 2007 Microchip Technology Inc.
R/W-0
x = Bit is unknown
POR
(2)
R/W-0
BOR
bit 0