PIC18F4585-E/ML Microchip Technology, PIC18F4585-E/ML Datasheet - Page 213

• Manufacturer Part Number: PIC18F4585-E/ML
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,LLCC,44PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4585-E/ML

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 48KB (24K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.25K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 44-QFN
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.25 KB
• Interface Type: I2C, SPI, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 44
• Number Of Timers: 1 x 8
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11 bit
• Height: 0.88 mm
• Length: 8 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 8 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3-DB18F4680 - BOARD DAUGHTER ICEPIC3
• Lead Free Status / Rohs Status: Details

17.4.6
Master mode is enabled by setting and clearing the
appropriate SSPM bits in SSPCON1 and by setting the
SSPEN bit. In Master mode, the SCL and SDA lines
are manipulated by the MSSP hardware.
Master mode of operation is supported by interrupt
generation on the detection of the Start and Stop
conditions. The Stop (P) and Start (S) bits are cleared
from a Reset or when the MSSP module is disabled.
Control of the I
set or the bus is Idle, with both the S and P bits clear.
In Firmware Controlled Master mode, user code
conducts all I
Stop bit conditions.
Once Master mode is enabled, the user has six
options.
1.
2.
3.
4.
5.
6.
FIGURE 17-16:
© 2007 Microchip Technology Inc.
Assert a Start condition on SDA and SCL.
Assert a Repeated Start condition on SDA and
SCL.
Write
transmission of data/address.
Configure the I
Generate an Acknowledge condition at the end
of a received byte of data.
Generate a Stop condition on SDA and SCL.
SDA
SCL
MASTER MODE
to
2
C bus operations based on Start and
2
C bus may be taken when the P bit is
the
2
C port to receive data.
SSPBUF
MSSP BLOCK DIAGRAM (I
SDA In
register
Bus Collision
SCL In
initiating
Read
PIC18F2585/2680/4585/4680
MSb
Write Collision Detect
Preliminary
Start bit, Stop bit,
end of XMIT/RCV
State Counter for
Clock Arbitration
Acknowledge
Start bit Detect
Stop bit Detect
SSPBUF
2
Generate
SSPSR
C™ MASTER MODE)
The following events will cause the SSP Interrupt Flag
bit, SSPIF, to be set (SSP interrupt, if enabled):
• Start condition
• Stop condition
• Data transfer byte transmitted/received
• Acknowledge transmit
• Repeated Start
LSb
Note:
Write
Clock
Data Bus
Shift
Internal
Set/Reset, S, P, WCOL (SSPSTAT)
Set SSPIF, BCLIF
Reset ACKSTAT, PEN (SSPCON2)
The MSSP module, when configured in
I
of events. For instance, the user is not
allowed to initiate a Start condition and
immediately write the SSPBUF register to
initiate transmission before the Start
condition is complete. In this case, the
SSPBUF will not be written to and the
WCOL bit will be set, indicating that a write
to the SSPBUF did not occur.
2
C Master mode, does not allow queueing
SSPADD<6:0>
SSPM3:SSPM0
Generator
DS39625C-page 211
Baud
Rate