PAXDR000 Red Lion Controls, PAXDR000 Datasheet - Page 23

• Manufacturer Part Number: PAXDR000
• Description: AC, Dual Rate, Upgradeable Red
• Manufacturer: Red Lion Controls
• Type: Rate/Totalizerr

Specifications of PAXDR000

• Accuracy: ± (0.01% of Input Signal Frequency)
• Cut Out, Panel: 3.62W x 1.77H Inches
• Dimensions: 3.80W x 1.95H Inches
• Display Digit Height: .56 Inches
• Display Type: LED Adjustable
• Function: Rate/Totalizer
• Input Type: Switch Selectable Pulse
• Keypad Type: 3 Programmable Function (5 Keys Total)
• Number Of Digits: Rate = 5, Totalizer = 8
• Primary Type: Electronic
• Range, Measurement: Rate = 0 to 99999, Totalizer = ±99999999
• Special Features: Programmable Function Keys
• Termination: Cage Clamp
• Voltage, Supply: 85 to 250 VAC
• Lead Free Status / Rohs Status: RoHS Compliant part

Parameters. These parameters are used to match the serial settings of the meter
with those of the host computer or other serial device, such as a terminal or
printer. This programming module can only be accessed if an RS232 or RS485
Serial Communications card is installed.
required for communicating with the PAXDR. In order to establish serial
communications, the user must have host software that can send and receive
ASCII characters. For serial hardware and wiring details, refer to section 4.5
Serial Communication Wiring.
communications plug-in cards. Discard the separate bulletin when using those
serial plug-in cards with the PAXDR. Also, this section does NOT apply to the
DeviceNet, Modbus, or Profibus-DP communication cards. For details on the
operation of the Fieldbus cards, refer to the bulletin shipped with each card.

serial link. Normally, the baud rate is set to the highest value that all the serial
equipment are capable of transmitting and receiving.

other serial communications equipment on the serial link.

on the serial link. The meter ignores the parity when receiving data and sets the
parity bit for outgoing data. If no parity is selected with 7 bit word length, an
additional stop bit is used to force the frame size to 10 bits.
6.7 MODULE 7 - S
Module 7 is the programming module for the Serial Communications
This section also includes an explanation of the commands and formatting
This section replaces the bulletin shipped with the RS232 and RS485 serial
Set the baud rate to match the other serial communications equipment on the
Select either 7 or 8 bit data word lengths. Set the word length to match the
Set the parity bit to match that of the other serial communications equipment



PAR

7-SrL
Baud Rate

PAR
bAUd
A rAtE



Rate A

Print




BAUD RATE
Data Bit
PARITY BIT
b rAtE
DATA BIT
dAtA
Rate B
Print





ERIAL
C rAtE


Rate C
Parity Bit
Print
PAr

C
PARAMETER MENU
Total A & B
OMMUNICATIONS
Ab tot
Print
Address
Meter
Addr
23
23
C tot
Total C

needed and a value of zero can be used. With multiple units (RS485
applications), a unique 2 digit address number must be assigned to each meter.

parameter data and mnemonics) or
(parameter data only). This will affect all the parameters selected in the print
options. (If the meter address is 00, it will not be sent during a full transmission.)

print request. For each parameter in the sub-menu, select
information to be sent during a print request or
not to be sent. A print request is sometimes referred to as a block print because
more than one parameter's information (meter address, parameter data and
mnemonics) can be sent to a printer or computer as a block.
Print
PARAMETER
Enter the serial meter (node) address. With a single unit, an address is not
Select

*Setpoints are plug-in card dependent.




Abbreviated





Printing
- Enters the sub-menu to select the meter parameters to appear during a


Abbr

Scale Factors
for full print or Command T transmissions (meter address,





DESCRIPTION
Rate A
Rate B
Rate C
Total A & B
Total C
A B C Scale Factors
A B Count Load
1 2 3 4 Setpoints *
SCFAC

Print
P
YES
ARAMETERS
ABBREVIATED PRINTING

Options
METER ADDRESS
Print
to
PRINT OPTIONS
OPt


Count Load
CntLd
Values
Print

NO

for abbreviated print transmissions
FACTORY









(
SPt
for that parameter information

Setpoint
Values
Print

MNEMONIC
RTA
RTB
RTC
TOA TOB
TOC
SFA SFB SFC
LDA LDB
SP1 SP2 SP3 SP4
for that parameter
Pro
)