PAXDR000 Red Lion Controls, PAXDR000 Datasheet - Page 5

• Manufacturer Part Number: PAXDR000
• Description: AC, Dual Rate, Upgradeable Red
• Manufacturer: Red Lion Controls
• Type: Rate/Totalizerr

Specifications of PAXDR000

• Accuracy: ± (0.01% of Input Signal Frequency)
• Cut Out, Panel: 3.62W x 1.77H Inches
• Dimensions: 3.80W x 1.95H Inches
• Display Digit Height: .56 Inches
• Display Type: LED Adjustable
• Function: Rate/Totalizer
• Input Type: Switch Selectable Pulse
• Keypad Type: 3 Programmable Function (5 Keys Total)
• Number Of Digits: Rate = 5, Totalizer = 8
• Primary Type: Electronic
• Range, Measurement: Rate = 0 to 99999, Totalizer = ±99999999
• Special Features: Programmable Function Keys
• Termination: Cage Clamp
• Voltage, Supply: 85 to 250 VAC
• Lead Free Status / Rohs Status: RoHS Compliant part

case by firmly squeezing and pulling back on the side rear finger tabs. This
should lower the latch below the case slot (which is located just in front of the
finger tabs). It is recommended to release the latch on one side, then start the
other side latch.
2.1 SETTING THE JUMPER
this jumper must be set before applying power. The Main Circuit Board figure
shows the location of the jumper and DIP switch.
are used with user functions or for input signal direction. All user inputs are set
by this jumper.
1.0 I
2.0 S
Installation
unit is intended to be mounted into an enclosed panel. Prepare the panel cutout
to the dimensions shown. Remove the panel latch from the unit. Slide the panel
gasket over the rear of the unit to the back of the bezel. The unit should be
installed fully assembled. Insert the unit into the panel cutout.
To access the jumper and switches, remove the meter base from the meter
The meter has one jumper for user input logic. When using the user inputs
The user input jumper determines signal logic for the user inputs, when they
The PAX meets NEMA 4X/IP65 requirements when properly installed. The
PANEL
BEZEL
GASKET
NSTALLING THE
ETTING THE
LATCHING
SLOTS
INPUT SET-UP
DIP SWITCHES
Main
Circuit
Board
PANEL
SRC
J
UMPER AND
PANEL
MOUNTING
SCREWS
SNK
USER
INPUT
JUMPER
M
PANEL
LATCH
ETER
LATCHING
TABS
5
so that the tabs of the panel latch engage in the slots on the case. The panel
latch should be engaged in the farthest forward slot possible. To achieve a
proper seal, tighten the latch screws evenly until the unit is snug in the panel
(Torque to approximately 7 in-lbs [79N-cm]). Do not over-tighten the screws.
Installation Environment
temperature and provides good air circulation. Placing the unit near devices
that generate excessive heat should be avoided.
Do NOT use solvents. Continuous exposure to direct sunlight may accelerate
the aging process of the bezel.
keypad of the unit.
2.2 SETTING THE INPUT DIP SWITCHES
must be set before applying power.
SWITCHES 1 and 4
LOGIC: Input trigger levels V
MAG: 200 mV peak input (must also have SRC on). Not recommended with
counting applications.
SWITCHES 2 and 5
SNK.: Adds internal 7.8 K pull-up resistor to +12 VDC, I
SRC.: Adds internal 3.9 K pull-down resistor, 7.3 mA max. @ 28 VDC,
V
SWITCHES 3 and 6
HI Frequency: Removes damping capacitor and allows max. frequency.
LO Frequency: Adds a damping capacitor for switch contact bounce. Also
MAX
While holding the unit in place, push the panel latch over the rear of the unit
The unit should be installed in a location that does not exceed the operating
The bezel should only be cleaned with a soft cloth and neutral soap product.
Do not use tools of any kind (screwdrivers, pens, pencils, etc.) to operate the
The meter has six DIP switches for Input A and Input B terminal set-up that
limits input frequency to 50 Hz and input pulse widths to 10 msec.
= 30 VDC.
Warning: Exposed line voltage exists on the circuit boards. Remove
DIP S
all power to the meter and load circuits before accessing inside of
the meter.
Input B LO Freq.
Input B SRC.
Input B MAG.
Input A LO Freq.
Input A SRC.
Input A MAG.
3.62
IL
ON
(92
PANEL CUT-OUT
WITCHES
= 1.5 V max.; V
+.03
+.8
-.00
-.0
Factory Setting
)
4
3
1
6
5
2
HI Freq.
SNK.
Logic
HI Freq.
SNK.
Logic
IH
= 3.75 V min.
1.77
(45
MAX
+.02
+.5
-.00
-.0
)
= 1.9 mA.