ETRX2HR-PA Telegesis Ltd, ETRX2HR-PA Datasheet - Page 7

• Manufacturer Part Number: ETRX2HR-PA
• Description: MODULE
• Manufacturer: Telegesis Ltd

Specifications of ETRX2HR-PA

• Module Applications: AMR, Building Automation, Wireless Sensor Network, M2M Industrial Controls
• Mcu Supported Families: EM250
• Processor Type: EM250
• Wireless Protocol: IEEE 802.15.4
• Data Rate: 250Kbps
• Module Interface: I2C, SPI, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The FCC requires the user to be notified that any changes or modifications made to this device
that are not expressly approved by Telegesis (UK) Ltd. may void the user's authority to operate the
equipment.
When using the ETRX2HR-PA with approved antennae, it is required to prevent end-users from
replacing them with non-approved ones.
2.1.1
When integrating the ETRX2-PA or ETRX2HR-PA into a product if must be ensured that the FCC
labelling requirements are met. This includes a clearly visible label on the outside of the finished
product specifying the Telegesis FCC identifier (FCC ID: T7VEM250B) as well as the notice
above. This exterior label can use wording such as “Contains Transmitter Module FCC ID:
T7VEM250B” or “Contains FCC ID: T7VEM250B” although any similar wording that expresses
the same meaning may be used.
2.2 European Certification
The ETRX2-PA and ETRX2HR-PA are certified at a power level of 21.15mW e.i.r.p. (13.2dBm) to
the following standards:
The ETRX2HR-PA was tested with the antennae listed in Table 1.
If the ETRX2-PA or ETRX2HR-PA module is incorporated into an OEM product, the OEM product
manufacturer must ensure compliance of the final product to the European Harmonised EMC, and
low voltage/safety standards. A Declaration of Conformity must be issued for each of these
standards and kept on file as described in the R&TTE Directive. The final product must not exceed
the specified power ratings, antenna specifications and installation requirements as specified in
this ETRX2-PA user manual. If any of these specifications are exceeded in the final product then a
submission must be made to a notified body for compliance testing to all of the required standards.
The ‘CE’ marking must be applied to a visible location on any OEM product. For more information
please
responsibility for learning and meeting the required guidelines for each country in their distribution
market.
Important Note: In Europe the regulations for the 2.4GHz frequency band are only harmonized for
devices with an e.i.r.p. of less than 10mW (10dBm). In the case of e.i.r.p. of more than 10mW the
manufacturer or his authorised representative established within the community or the person
responsible for placing the equipment on the market shall notify the national authority responsible
in the relevant Member State for spectrum management of the intention to place such equipment
on its national market. This notification shall be given no less than four weeks in advance of the
start of placing on the market.
Because of this Telegesis recommends that the user limit the output power to 10mW (10dBm) for
Europe to avoid having to deal with the local authorities for spectrum management of each
relevant member state.
©2009 Telegesis (UK) Ltd
•
•
•
0681
Radio:
EMC:
Safety:
FCC Labelling Requirements
refer
EC-R&TTE Certificated
to
http://ec.europa.eu/enterprise/faq/ce-mark.htm.
EN 300 328 v1.7.1 (10/2006)
EN 301 489-17 v1.2.1 (08/2002)
EN 60950-1:2006
- 7 -
ETRX2PA Product Manual (Rev 1.07)
Customers
assume
ETRX2PA
full