DS26514DK Maxim Integrated Products, DS26514DK Datasheet - Page 91

• Manufacturer Part Number: DS26514DK
• Description: Power Management Modules & Development Tools 4-Port T1-E1-J1 Tran Transceiver Demo Kit
• Manufacturer: Maxim Integrated Products

Specifications of DS26514DK

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.12.2.2
The DS26514 can transmit a 2.048MHz square-wave synchronization clock as specified in Section 10 of ITU-T
G.703. To use this mode, set the transmit G.703 synchronization clock bit (TG703) found in the LIU Transmit
Impedance and Pulse Shape Selection Register (LTIPSR). This mode also requires a 1μF blocking capacitor
between TTIPn and the transformer. Additionally, the following registers should set to center the pulse to meet the
pulse template:
9.12.2.3
The individual transmitters can be powered down by setting the TPDE bit in the LIU Maintenance Control Register
(LMCR). Note that powering down the transmit LIU results in a high-impedance state for the corresponding TTIPn
and TRINGn pins.
When transmit all ones (AIS) is invoked, continuous ones are transmitted using MCLK as the timing reference.
Data input from the framer is ignored. AIS can be sent by setting a bit in the
also be sent if the corresponding receiver goes into LOS state and the ATAIS bit is set in the LMCRl register.
9.12.2.4
Each transmitter has an automatic short-circuit current limiter that activates when the load resistance is
approximately 25Ω or less. TSCS (LRSR.2) provides a real-time indication of when the current limiter is activated.
The LIU Latched Status Register (LLSR) provides latched versions of the information, which can be used to
activate an interrupt when enable via the
9.12.2.5
The DS26514 can also detect when the TTIPn or TRINGn outputs are open circuited. OCS (LRSR.1) will provide a
real-time indication of when an open circuit is detected. Register
which can be used to activate an interrupt when enabled via the
not available in T1 CSU operating modes (LBO 5, LBO 6, and LBO 7).
9.12.3 Receiver
9.12.3.1
The DS26514 contains four receivers. The termination circuit provides an analog switch that powers up in the open
setting, providing high impedance to the receive line side. This is useful for redundancy applications and hot
swapability.
Three termination methods are available:
See the
termination by setting the appropriate RIMPM[1:0] bits. These bits must be configured to match line impedance
even if internal termination is disabled.
Figure 9-24
external resistor, R
Figure 9-24. Receive LIU Termination Options
Rev: 101608
•
•
•
Partially internal impedance match with 120Ω external resistor.
Fully internal impedance match, no external resistor.
External resistor termination, internal termination disabled.
LRISMR
If configuring for E1 120Ω mode, set register addresses 0x1229 = 0xF8 and 0x122D = 0x09.
shows a diagram of the switch control of termination. If internal impedance match is disabled, the
Transmit G.703 Section 10 Synchronization Signal
Transmit Power-Down
Transmit Short-Circuit Detector/Limiter
Transmit Open-Circuit Detector
Receive Internal Termination
register for more details. Internal impedance match is configurable to 75Ω, 100Ω, 110Ω, or 120Ω
T
, must match the line impedance.
If configuring for E1 75Ω mode, set register address 0x1229 = 0xF8.
LSIMR
register.
LLSR
LSIMR
provides latched versions of the information,
register. The open-circuit-detect feature is
DS26514 4-Port T1/E1/J1 Transceiver
LMCR
register. Transmit all ones will
91 of 305