CS8900A-IQ3ZR Cirrus Logic Inc, CS8900A-IQ3ZR Datasheet - Page 67
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CS8900A-IQ3ZR
Manufacturer Part Number
CS8900A-IQ3ZR
Description
Ethernet ICs IC 10Mbps Ethernet Controller 3.3V
Manufacturer
Cirrus Logic Inc
Datasheet
1.CS8900A-CQZ.pdf
(138 pages)
Specifications of CS8900A-IQ3ZR
Ethernet Connection Type
10Base- 2, 10Base- 5, 10Base- F, 10Base- T
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Product
Ethernet Controllers
Standard Supported
IEEE 802.3
Data Rate
10 Mbps
Maximum Operating Temperature
+ 85 C
Package / Case
LQFP-100
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS8900A-IQ3ZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
DS271F5
TxBidErr
Rdy4TxNOW
Reset value is: 0000 0000 0001 1000
4.4.22 Register 19: Test Control
(TestCTL, Read/Write, Address: PacketPage base + 0118h)
TestCTL controls the diagnostic test modes of the CS8900A.
011001
DisableLT
ENDECloop
AUIloop
CS8900A
Crystal LAN™ Ethernet Controller
DisableLT
7
F
FDX
Register. When reading this register, these bits will be 011000, where the LSB corresponds to
Bit 0.
send. Frames that the CS8900A will not send are:
1) Any frame greater than 1514 bytes, provided that InhibitCRC
2) Any frame greater than 1518 bytes.
Note that this bit is not set when transmit frames are too short.
transmission. This bit is similar to Rdy4Tx (Register C, BufEvent, Bit 8) except that there is no
interrupt associated with Rdy4TxNOW. The host can poll the CS8900A and check
Rdy4TxNOW to determine if the CS8900A is ready for transmit. (See Section 5.6 on page 99
for a description of the transmit bid process.)
Register.
link status. DisableLT is used in conjunction with the LinkOK (Register 14, LineST, Bit 7) as fol-
lows:
LinkOK
output is connected to the decoder input. The 10BASE-T and AUI transmitters and receivers
are disabled. When clear, the CS8900A is configured for normal operation.
the AUI. When clear, the CS8900A is configured for normal AUI operation.
If set, the host has commanded the CS8900A to transmit a frame that the CS8900A will not
Rdy4TxNOW signals the host that the CS8900A is ready to accept a frame from the host for
These bits provide an internal address used by the CS8900A to identify this as the Test Control
When set, the 10BASE-T interface allows packet transmission and reception regardless of the
When set, the CS8900A enters internal loopback mode where the internal Manchester encoder
When set, the CS8900A allows reception while transmitting. This facilitates loopback tests for
E
6
(Register 9, TxCMD, Bit C) is clear.
0
0
1
D
5
DisableLT
CIRRUS LOGIC PRODUCT DATASHEET
0
1
X
No packet transmission or reception allowed.
Transmitter sends link pulses.
DisableLT overrides LinkOK to allow packet transmission and
reception.
Disable has no meaning if LinkOK = 1.
C
4
Disable Back-
off
B
3
011001
AUIloop
A
2
ENDEC loop
1
9
0
8
67