327913-000 Tyco Electronics, 327913-000 Datasheet - Page 411

• Manufacturer Part Number: 327913-000
• Description: Connector Accessories Hexa Shield Adapter Aluminum Alloy Olive Drab
• Manufacturer: Tyco Electronics
• Type: Hexa Shield Adapterr

Table B. D-129/141/71X Series
(up to 150°C [302°F] rated)
Connection-point
Type and Size
For Fine Wire Terminations
0.15 mm
Smaller*
Catalog 1654025
Revised 12-04
www.tycoelectronics.com
Dimensions
Terminal
post
pin
tab
2
W
W
W
(26 AWG) and
W = up to 0.61 [.024]
W = 0.63 [.025] to
W = 0.76 [.030] to
W = up to 1.52 [.060]
W = 1.27 [.050] to
W = 2.28 [.090] to
Dimensions are in millimeters
and inches unless otherwise
specified. Values in brackets
are U.S. equivalents.
1.27 [.050]
0.81 [.032]
2.28 [.090]
3.55 [.140]
Wire Termination to Pin/Post/Tab
Note: Micro SolderSleeve terminators are used for attaching leads smaller than 26 AWG (0.15 mm
than 0.6 [.025] wide.
*The D-110 series sleeves are primarily for single wire terminations and do not have a wire stop. The D-141 series will
**Minimum. Wire insulation must be smaller than this. When using the D-141 parts for two-wire terminations, the com-
†Maximum. The combination of conductor diameter and terminal width and the wire insulation must be greater than
††The terminal length should be at least 1.2 [0.05] shorter than this. The wire strip length must be adjusted so that,
SolderSleeve Discrete Wire Terminators
accept either one or two wires; the parts have a built-in wire stop that will locate the wire approximately 0.76 [0.03]
from bottom of terminal.
this.
bined wire insulation diameters must be less than 1.5 [.060].
when terminated, the exposed conductor is covered by the sleeve.
D-110-0062
D-110-0217
D-141-13
D-141-22
D-141-30
No.*
Part
30–26
24–22
24–20
24–20
24–20
24–20
AWG
20
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Wire
[0.05–0.15]
[0.24–0.38]
[0.24–0.61]
[0.24–0.61]
[0.24–0.61]
[0.24–0.61]
0.75 x 1.65 [0.030 X 0.065]
0.75 x 1.65 [0.030 X 0.065]
0.75 x 1.65 [0.030 X 0.065]
[0.61]
mm
2
Inside Diameter
As Supplied**
1.0 [0.040]
1.0 [0.040]
D-129-0043
D-141-30
D-141-07
D-141-31
D-141-56
D-129-05
D-129-03
None
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
Tape Carrier Spacing of Sleeves (Center-to-Center)
(Continued)
D-713-03
[0.050]
1.27
—
—
—
—
—
—
0.75 [0.030]
0.75 [0.030]
0.75 [0.030]
Recovered†
0.6 [0.025]
0.6 [0.025]
Fully
D-714-01
D-711-00
D-711-04
[0.100]
2.54
—
—
—
—
South America: 55-11-3611-1514
Japan: 81-44-900-5102
Singapore: 65-4866-151
UK: 44-1793-528171
D-711-07
[0.125]
3.17
—
—
—
—
—
—
16.0 [0.630]
9.0 [0.360]
4.7 [0.185]
6.0 [0.240]
9.5 [0.375]
2
) to terminals less
Length††
D-714-00
D-711-08
[0.156]
4.0
—
—
—
—
—
8-41
8