M25P20-VMN6PB NUMONYX, M25P20-VMN6PB Datasheet - Page 41

• Manufacturer Part Number: M25P20-VMN6PB
• Description: Flash Mem Serial-SPI 3.3V 2M-Bit 256K x 8 8ns 8-Pin SO N Tray
• Manufacturer: NUMONYX

Specifications of M25P20-VMN6PB

• Package: 8SO N
• Cell Type: NOR
• Density: 2 Mb
• Architecture: Sectored
• Block Organization: Symmetrical
• Typical Operating Supply Voltage: 3.3 V
• Sector Size: 64KByte x 4
• Timing Type: Synchronous
• Operating Temperature: -40 to 85 °C
• Interface Type: Serial-SPI

Table 20.
1. 40MHz is the maximum frequency for T9HX device operation in the extended Vcc range 2.3 V to 2.7 V.
2. Details of how to find the date of marking are given in Application Note, AN1995.
3. t
4. Value guaranteed by characterization, not 100% tested in production.
5. Expressed as a slew-rate.
6. Only applicable as a constraint for a WRSR instruction when SRWD is set at 1.
Symbol
t
t
t
t
t
t
t
t
t
HHQX
WHSL
SHWL
CLCH
CHCL
SHQZ
HLQZ
RES1
RES2
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
CH
DVCH
CHDX
CHSH
SHCH
CHHH
HHCH
SLCH
CHSL
CLQV
CLQX
HLCH
CHHL
CL
SHSL
DP
CH
f
f
C
R
(3)
(4)
(3)
(4)
(4)
(4)
(4)
(4)
+ t
(4)
(4)
(6)
(6)
CL
must be greater than or equal to 1/ f
t
t
t
t
t
AC Characteristics (40MHz Operation, Device Grade 6)
Alt.
t
t
CSS
DSU
t
CSH
t
40MHz available for products marked since week 20 of 2004, only
CLH
t
CLL
DIS
f
DH
HO
t
HZ
LZ
C
V
Clock Frequency for the following
instructions: FAST_READ, PP, SE, BE,
DP, RES, WREN, WRDI, RDSR, WRSR
Clock Frequency for READ instructions
Clock High Time
Clock Low Time
Clock Rise Time
Clock Fall Time
S Active Setup Time (relative to C)
S Not Active Hold Time (relative to C)
Data In Setup Time
Data In Hold Time
S Active Hold Time (relative to C)
S Not Active Setup Time (relative to C)
S Deselect Time
Output Disable Time
Clock Low to Output Valid
Output Hold Time
HOLD Setup Time (relative to C)
HOLD Hold Time (relative to C)
HOLD Setup Time (relative to C)
HOLD Hold Time (relative to C)
HOLD to Output Low-Z
HOLD to Output High-Z
Write Protect Setup Time
Write Protect Hold Time
S High to Deep Power-down Mode
S High to Standby Mode without
Electronic Signature Read
S High to Standby Mode with Electronic
Signature Read
Test conditions specified in
Parameter
(5)
(5)
(peak to peak)
(peak to peak)
C
Table 10
and
D.C.
Min.
D.C.
100
100
0.1
0.1
11
11
20
5
5
2
5
5
5
0
5
5
5
5
Table 18
Typ.
(1)
1.8 or 30
3 or 30
Max.
(2)
40
20
9
9
9
9
3
(7)
(7)
MHz
MHz
Unit
V/ns
V/ns
41/55
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
μs
μs
μs
ns