MT41J256M8HX-15E:D Micron Technology Inc, MT41J256M8HX-15E:D Datasheet - Page 121

• Manufacturer Part Number: MT41J256M8HX-15E:D
• Description: MICMT41J256M8HX-15E:D 2GB:X4,X8,X16 DDR3
• Manufacturer: Micron Technology Inc
• Type: DDR3 SDRAMr
• Series: -r

Specifications of MT41J256M8HX-15E:D

• Organization: 256Mx8
• Address Bus: 18b
• Maximum Clock Rate: 1.333GHz
• Operating Supply Voltage (typ): 1.5V
• Package Type: FBGA
• Operating Temp Range: 0C to 95C
• Operating Supply Voltage (max): 1.575V
• Operating Supply Voltage (min): 1.425V
• Supply Current: 165mA
• Pin Count: 78
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Format - Memory: RAM
• Memory Type: DDR3 SDRAM
• Memory Size: 2G (256M x 8)
• Speed: 667MHz
• Interface: Parallel
• Voltage - Supply: 1.425 V ~ 1.575 V
• Operating Temperature: 0°C ~ 95°C
• Package / Case: 78-TFBGA
• Lead Free Status / RoHS Status: Compliant

Figure 43: DLL Disable Mode to DLL Enable Mode
PDF: 09005aef826aaadc
2Gb_DDR3_SDRAM.pdf – Rev. K 04/10 EN
Command
ODT 10
CK#
CKE
CK
ODTL off + 1 × t CK
7
NOP
T0
Notes:
SRE 1
Ta0
The clock frequency range for the DLL disable mode is specified by the parameter
t
supported.
DLL disable mode will affect the read data clock to data strobe relationship (
but not the data strobe to data relationship (
line up read data to the controller time domain.
Compared to the DLL on mode where
cycles after the READ command, the DLL disable mode
after the READ command.
WRITE operations function similarly between the DLL enable and DLL disable modes;
however, ODT functionality is not allowed with DLL disable mode.
CKdll_dis. Due to latency counter and timing restrictions, only CL = 6 and CWL = 6 are
10. Static LOW in the case that R
1. Enter SELF REFRESH.
2. Exit SELF REFRESH.
3. Wait
4. Wait
5. Wait
6. Wait
7. Starting with the idle state.
8. Change frequency.
9. Clock must be stable at least
t CKSRE
NOP
Ta1
t
t
t
t
XS, then set MR1[0] to 0 to enable DLL.
MRD, then set MR0[8] to 1 to begin DLL RESET.
MRD, update registers (CL, CWL, and write recovery may be necessary).
MOD, any valid command.
Tb0
t CKESR
8
Tc0
121
TT,nom
t
t CKSRX 9
CKSRX.
Tc1
or R
t
DQSCK starts from the rising clock edge AL + CL
Micron Technology, Inc. reserves the right to change products or specifications without notice.
TT(WR)
SRX 2
Td0
t
DQSQ,
2Gb: x4, x8, x16 DDR3 SDRAM
is enabled; otherwise, static LOW or HIGH.
t XS
MRS 3
Te0
t
QH). Special attention is needed to
t MRD
t
Indicates A Break in
Time Scale
DQSCK starts AL + CL - 1 cycles
MRS 4
Tf0
© 2006 Micron Technology, Inc. All rights reserved.
t MRD
t DLLK
MRS 5
Tg0
Commands
t
Don’t Care
DQSCK)
Valid 6
Valid
Th0