LTC1406IGN#TR Linear Technology, LTC1406IGN#TR Datasheet - Page 13

• Manufacturer Part Number: LTC1406IGN#TR
• Description: IC ADC 8BIT 20MSPS SAMPLE 24SSOP
• Manufacturer: Linear Technology

Specifications of LTC1406IGN#TR

• Number Of Bits: 8
• Sampling Rate (per Second): 20M
• Data Interface: Parallel
• Number Of Converters: 1
• Power Dissipation (max): 225mW
• Voltage Supply Source: Analog and Digital, Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-SSOP (0.150", 3.90mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

APPLICATIONS
shutdown. It may also be desirable to isolate the data out-
put pins from the bus to reduce the load capacitance. To
resume normal operation the SHDN pin must be brought
high and typically 20 clock cycles must be performed at a
sample rate above 10kHz before the output data will be
valid.
Board Layout and Bypassing
Wire wrap boards are not recommended for high resolu-
tion or high speed A/D converters. To obtain the best per-
formance from the LTC1406, a printed circuit board with
ground plane is required. Layout for the printed circuit
board should ensure that digital and analog signal lines are
separated as much as possible. In particular, care should
be taken not to run any digital track alongside an analog
signal track or underneath the ADC.
An analog ground plane separate from the logic system
ground should be established under and around the ADC.
Pin 1 (OGND), Pin 6 (AGND), Pin 10 (AGND) and Pin 11
(DGND) and all other analog grounds should be connected
to this single analog ground point. The V
and OV
this analog ground plane. No other digital grounds should
be connected to this analog ground plane. In some appli-
cations it may be desirable to connect the OV
system supply and OGND to the logic system ground. In
these cases OV
the analog ground plane.
Low impedance analog and digital power supply common
returns are essential to low noise operation of the ADC and
the foil width for these tracks should be as wide as pos-
sible. In applications where the ADC data outputs and
control signals are connected to a continuously active
DD
bypass capacitors should also be connected to
DD
should be bypassed to OGND instead of
U
INFORMATION
U
W
CM
DD
, V
to the logic
U
REF
, DV
DD
microprocessor bus, it is possible to get errors in the con-
version results. These errors are due to feedthrough from
the microprocessor to the comparators. The problem can
be eliminated by forcing the microprocessor into a wait
state during conversion or by using three-state buffers to
isolate the ADC data bus.
The LTC1406 has differential inputs to minimize noise cou-
pling. Common mode noise on the A
be rejected by the input CMRR. The LTC1406 will hold and
convert the difference voltage between A
leads to A
short as possible. In applications where this is not pos-
sible, the A
to equalize coupling.
Supply Bypassing
High quality, low series resistance ceramic, 10 F bypass
capacitors should be used at the V
as shown in the Typical Application on the first page of this
data sheet. Surface mount ceramic capacitors such as
Murata GRM235Y5V106Z016 provide excellent bypass-
ing in a small board space. Alternatively, 10 F tantalum
capacitors in parallel with 0.1 F ceramic capacitors can be
used. Bypass capacitors must be located as close to the
pins as possible. The traces connecting the pins and the
bypass capacitors must be kept short and should be made
as wide as possible.
Example Layout
Figures 12a, 12b, 12c and 12d show the schematic and
layout of an evaluation board. The layout demonstrates the
proper use of decoupling capacitors and ground plane
with a 2-layer printed circuit board.
IN
IN
+
+
(Pin 7) and A
and A
IN
–
traces should be run side by side
IN
–
(Pin 8) should be kept as
DD
IN
, V
+
and A
CM
IN
LTC1406
+
and V
and A
IN
–
leads will
REF
IN
13
–
. The
pins