PIC18F65K90-I/MR Microchip Technology, PIC18F65K90-I/MR Datasheet - Page 264

• Manufacturer Part Number: PIC18F65K90-I/MR
• Description: 32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm TUBE
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F65K90-I/MR

• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 8
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 53
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN Exposed Pad
• Lead Free Status / Rohs Status: Details

PIC18F87K90 FAMILY
FIGURE 19-11:
19.4.3
When any PWM mode is used, the application
hardware must use the proper external pull-up and/or
pull-down resistors on the PWM output pins.
The CCPxM<1:0> bits of the CCPxCON register allow
the user to choose whether the PWM output signals are
active-high or active-low for each pair of PWM output
pins (PxA/PxC and PxB/PxD). The PWM output
polarities must be selected before the PWM pin output
drivers are enabled. Changing the polarity configura-
tion while the PWM pin output drivers are enabled is
not recommended since it may result in damage to the
application circuits.
The PxA, PxB, PxC and PxD output latches may not be
in the proper states when the PWM module is
initialized. Enabling the PWM pin output drivers at the
same time as the Enhanced PWM modes may cause
damage to the application circuit. The Enhanced PWM
modes must be enabled in the proper Output mode and
DS39957D-page 264
Note:
Note 1: All signals are shown as active-high.
Shoot-Through Current
External Switch C
External Switch D
2: T
3: T
START-UP CONSIDERATIONS
When the microcontroller is released from
Reset, all of the I/O pins are in the
High-Impedance
circuits must keep the power switch
devices in the OFF state until the micro-
controller drives the I/O pins with the
proper signal levels or activates the PWM
output(s).
ON
OFF
is the turn-on delay of power switch, QC, and its driver.
Potential
is the turn-off delay of power switch, QD, and its driver.
EXAMPLE OF PWM DIRECTION CHANGE AT NEAR 100% DUTY CYCLE
PxC
PxD
PxA
PxB
state.
The
Forward Period
external
PW
complete a full PWM cycle before enabling the PWM
pin output drivers. The completion of a full PWM cycle
is indicated by the TMR2IF or TMR4IF bit of the PIR1
or PIR5 register being set as the second PWM period
begins.
19.4.4
The PWM mode supports an Auto-Shutdown mode that
will disable the PWM outputs when an external
shutdown event occurs. Auto-Shutdown mode places
the PWM output pins into a predetermined state. This
mode is used to help prevent the PWM from damaging
the application.
The auto-shutdown sources are selected using the
ECCPxAS<2:0> bits (ECCPxAS<6:4>). A shutdown
event may be generated by:
• A logic ‘0’ on the pin that is assigned the FLT0
• Comparator C1
• Comparator C2
• Setting the ECCPxASE bit in firmware
A shutdown condition is indicated by the ECCPxASE
(Auto-Shutdown Event Status) bit (ECCPxAS<7>). If
the bit is a ‘0’, the PWM pins are operating normally. If
the bit is a ‘1’, the PWM outputs are in the shutdown
state.
input function
t1
ENHANCED PWM
AUTO-SHUTDOWN MODE
T
ON (2)
 2009-2011 Microchip Technology Inc.
T
T = T
Reverse Period
OFF
(3)
OFF
PW
– T
ON
(2,3)
(1)