EP3C120F484I7 Altera, EP3C120F484I7 Datasheet - Page 218

• Manufacturer Part Number: EP3C120F484I7
• Description: IC CYCLONE III FPGA 120K 484FBGA
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C120F484I7

• Number Of Logic Elements/cells: 119088
• Number Of Labs/clbs: 7443
• Total Ram Bits: 3981312
• Number Of I /o: 283
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 484-FBGA
• Family Name: Cyclone III
• Number Of Logic Blocks/elements: 119088
• # I/os (max): 283
• Frequency (max): 437.5MHz
• Process Technology: 65nm
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 119088
• Ram Bits: 3981312
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 484
• Package Type: FBGA
• For Use With: 544-2589 - KIT DEV EMB CYCLONE III EDITION544-2566 - KIT DEV DSP CYCLONE III EDITION544-2444 - KIT DEV CYCLONE III EP3C120
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Not Compliant

9–58
Cyclone III Device Handbook, Volume 1
Figure 9–29. Combining JTAG and AS Configuration Schemes
Notes to
(1) Connect these pull-up resistors to the V
(2) Power up the V
(3) Pin 6 of the header is a V
(4) The MSEL pin settings vary for different configuration voltage standards and POR time. To connect MSEL[3..0]for
(5) These are dual-purpose I/O pins. This nCSO pin functions as the FLASH_NCE pin in AP mode. The ASDO pin
(6) Power up V
(7) You must place the diodes and capacitors as close as possible to the Cyclone III device family. For effective voltage
device. For this value, refer to the
this pin is a no connect. In USB-Blaster and ByteBlaster II, this pin is connected to nCE when it is used for AS
programming, otherwise it is a no connect.
AS configuration schemes, refer to
functions as the DATA[1] pin in other AP and FPP modes.
V
cable. The MasterBlaster cable can receive power from either 5.0- or 3.3-V circuit boards, DC power supply, or 5.0 V
from the USB cable. For this value, refer to the
clamping, Altera recommends using the Schottky diode, which has a relatively lower forward diode voltage (VF) than
the switching and Zener diodes. For more information about the interface guidelines using Schottky diodes, refer to
AN 523: Cyclone III Configuration Interface Guidelines with EPCS Devices.
CCA
10-Pin Male Header
Download Cable
. Third-party programmers must switch to 2.5 V. Pin 4 of the header is a V
Figure
Chapter 9: Configuration, Design Security, and Remote System Upgrades in the Cyclone III Device Family
Configuration
(AS Mode)
Pin 1
Device
Serial
CC
DCLK
DATA
ASDI
9–29:
nCS
of the ByteBlaster II, USB-Blaster, ByteBlasterMV, or Ethernet Blaster cable with a 2.5- V supply from
3.3 V (2)
CC
10 kΩ
10kΩ
of the ByteBlaster II, USB-Blaster, or Ethernet Blaster cable with the 3.3-V supply.
V
CCIO
GND
IO
(1)
10 kΩ
reference voltage for the MasterBlaster output driver. V
V
10 pf
(7)
CCIO
(7)
GND
MasterBlaster Serial/USB Communications Cable User
3.3 V
(1)
10 kΩ
Table 9–7 on page
GND
3.3 V
V
CCIO
CCIO
GND
3.3 V
10 pf
supply of the bank in which the pin resides.
(1)
10 pf
3.3 V
MasterBlaster Serial/USB Communications Cable User
GND
Cyclone III Device Family
nSTATUS
CONF_DONE
nCONFIG
nCE
DATA[0]
DCLK
nCSO (5)
ASDO (5)
9–11. Connect the MSEL pins directly to V
10 pf
MSEL [3..0]
nCEO
TCK
TDO
TMS
TDI
© December 2009 Altera Corporation
N.C.
(4)
CC
V
power supply for the MasterBlaster
CCA
IO
must match the V
10 kΩ
V
1 kΩ
CCA
Guide. In ByteBlasterMV,
10 kΩ
GND
Configuration Features
10-Pin Male Header
Pin 1
Download Cable
CCA
(JTAG Mode)
(top view)
or GND.
Guide.
CCA
V
of the
CCA
V
IO
(6)
(3)