EP3C120F484I7 Altera, EP3C120F484I7 Datasheet - Page 241

• Manufacturer Part Number: EP3C120F484I7
• Description: IC CYCLONE III FPGA 120K 484FBGA
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C120F484I7

• Number Of Logic Elements/cells: 119088
• Number Of Labs/clbs: 7443
• Total Ram Bits: 3981312
• Number Of I /o: 283
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 484-FBGA
• Family Name: Cyclone III
• Number Of Logic Blocks/elements: 119088
• # I/os (max): 283
• Frequency (max): 437.5MHz
• Process Technology: 65nm
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 119088
• Ram Bits: 3981312
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 484
• Package Type: FBGA
• For Use With: 544-2589 - KIT DEV EMB CYCLONE III EDITION544-2566 - KIT DEV DSP CYCLONE III EDITION544-2444 - KIT DEV CYCLONE III EP3C120
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Not Compliant

Chapter 9: Configuration, Design Security, and Remote System Upgrades in the Cyclone III Device Family
Remote System Upgrade
© December 2009
1
Altera Corporation
After power up or a configuration error, the factory configuration logic writes the
remote system upgrade control register to specify the address of the application
configuration to be loaded. The factory configuration also specifies whether or not to
enable the user watchdog timer for the application configuration and, if enabled,
specifies the timer setting.
Only valid application configurations designed for remote update mode include the
logic to reset the timer in user mode. For more information about the user watchdog
timer, refer to
If there is an error while loading the application configuration, the remote system
upgrade status register is written by the dedicated remote system upgrade circuitry of
the Cyclone III device family, specifying the cause of the reconfiguration.
The following actions cause the remote system upgrade status register to be written:
■
■
■
■
Cyclone III device family automatically load the factory configuration located at
address boot_address[23:0] = 24'b0 for the AS configuration scheme, and
default address boot_address[23:0] = 24'h010000 (or the updated address if the default
address is changed) for the AP configuration scheme. This user-designed factory
configuration reads the remote system upgrade status register to determine the reason
for reconfiguration. Then the factory configuration takes the appropriate error
recovery steps and writes to the remote system upgrade control register to determine
the next application configuration to be loaded.
When Cyclone III device family successfully load the application configuration, the
devices enter user mode. In user mode, the soft logic (Nios II processor or state
machine and the remote communication interface) assists the Cyclone III device
family in determining when a remote system update is arriving. When a remote
system update arrives, the soft logic receives the incoming data, writes it to the
configuration memory device, and triggers the device to load the factory
configuration. The factory configuration reads the remote system upgrade status
register, determines the valid application configuration to load, writes the remote
system upgrade control register accordingly, and starts system reconfiguration.
nSTATUS driven low externally
Internal CRC error
User watchdog timer time-out
A configuration reset (logic array nCONFIG signal or external nCONFIG pin
assertion)
“User Watchdog Timer” on page
9–87.
Cyclone III Device Handbook, Volume 1
9–81