XC5202-6PC84C Xilinx Inc, XC5202-6PC84C Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
XC5202-6PC84C
Manufacturer Part Number
XC5202-6PC84C
Description
IC FPGA 64 CLB'S 84-PLCC
Manufacturer
Xilinx Inc
Series
XC5200r
Datasheet
1.XC5206-5PQ208C.pdf
(73 pages)
Specifications of XC5202-6PC84C
Number Of Logic Elements/cells
256
Number Of Labs/clbs
64
Number Of I /o
65
Number Of Gates
3000
Voltage - Supply
4.75 V ~ 5.25 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
84-LCC (J-Lead)
Dc
9629
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Total Ram Bits
-
Other names
122-1131
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XC5202-6PC84C
Manufacturer:
XILINX
Quantity:
1 980
Company:
Part Number:
XC5202-6PC84C
Manufacturer:
XILINX
Quantity:
1 980
Part Number:
XC5202-6PC84C
Manufacturer:
XILINX/赛灵思
Quantity:
20 000
XC5200 Series Field Programmable Gate Arrays
non-zero hold, attach a NODELAY attribute or property to
the flip-flop or input buffer.
IOB Output Signals
Output signals can be optionally inverted within the IOB,
and pass directly to the pad. As with the inputs, a CLB
flip-flop or latch can be used to store the output signal.
An active-High 3-state signal can be used to place the out-
put buffer in a high-impedance state, implementing 3-state
outputs or bidirectional I/O. Under configuration control,
the output (OUT) and output 3-state (T) signals can be
inverted. The polarity of these signals is independently
configured for each IOB.
The XC5200 devices provide a guaranteed output sink cur-
rent of 8 mA.
Supported destinations for XC5200-Series device outputs
are shown in
interface between 5 V and 3.3 V devices, see the 3V Prod-
ucts section of The Programmable Logic Data Book .)
An output can be configured as open-drain (open-collector)
by placing an OBUFT symbol in a schematic or HDL code,
then tying the 3-state pin (T) to the output signal, and the
input pin (I) to Ground. (See
Table 6: Supported Destinations for XC5200-Series
Outputs
Output Slew Rate
The slew rate of each output buffer is, by default, reduced,
to minimize power bus transients when switching non-criti-
cal signals. For critical signals, attach a FAST attribute or
property to the output buffer or flip-flop.
7-92
XC5200 device, V
CMOS-threshold inputs
Any typical device, V
CMOS-threshold inputs
Any device, V
TTL-threshold inputs
Any device, V
CMOS-threshold inputs
Figure 12: Open-Drain Output
1. Only if destination device has 5-V tolerant inputs
Destination
Table
CC
CC
= 5 V,
= 5 V,
CC
6.(For a detailed discussion of how to
=3.3 V,
CC
Product Obsolete or Under Obsolescence
= 3.3 V,
OBUFT
Figure
XC5200 Output Mode
12.)
OPAD
CMOS
some
X6702
5 V,
1
For XC5200 devices, maximum total capacitive load for
simultaneous fast mode switching in the same direction is
200 pF for all package pins between each Power/Ground
pin pair. For some XC5200 devices, additional internal
Power/Ground pin pairs are connected to special Power
and Ground planes within the packages, to reduce ground
bounce.
For slew-rate limited outputs this total is two times larger for
each device type: 400 pF for XC5200 devices. This maxi-
mum capacitive load should not be exceeded, as it can
result in ground bounce of greater than 1.5 V amplitude and
more than 5 ns duration. This level of ground bounce may
cause undesired transient behavior on an output, or in the
internal logic. This restriction is common to all high-speed
digital ICs, and is not particular to Xilinx or the XC5200
Series.
XC5200-Series devices have a feature called “Soft
Start-up,” designed to reduce ground bounce when all out-
puts are turned on simultaneously at the end of configura-
tion.
device starts up, the first activation of the outputs is auto-
matically slew-rate limited. Immediately following the initial
activation of the I/O, the slew rate of the individual outputs
is determined by the individual configuration option for
each IOB.
Global Three-State
A separate Global 3-State line (not shown in
forces all FPGA outputs to the high-impedance state,
unless boundary scan is enabled and is executing an
EXTEST instruction. This global net (GTS) does not com-
pete with other routing resources; it uses a dedicated distri-
bution network.
GTS can be driven from any user-programmable pin as a
global 3-state input. To use this global net, place an input
pad and input buffer in the schematic or HDL code, driving
the GTS pin of the STARTUP symbol. A specific pin loca-
tion can be assigned to this input using a LOC attribute or
property, just as with any other user-programmable pad. An
inverter can optionally be inserted after the input buffer to
invert the sense of the Global 3-State signal. Using GTS is
similar to Global Reset. See
details. Alternatively, GTS can be driven from any internal
node.
Other IOB Options
There are a number of other programmable options in the
XC5200-Series IOB.
Pull-up and Pull-down Resistors
Programmable IOB pull-up and pull-down resistors are
useful for tying unused pins to Vcc or Ground to minimize
power consumption and reduce noise sensitivity. The con-
figurable pull-up resistor is a p-channel transistor that pulls
When the configuration process is finished and the
November 5, 1998 (Version 5.2)
Figure 8 on page 90
Figure
11)
for
R