XC5202-6PC84C Xilinx Inc, XC5202-6PC84C Datasheet - Page 26
![no-image](/images/no-image-200.jpg)
XC5202-6PC84C
Manufacturer Part Number
XC5202-6PC84C
Description
IC FPGA 64 CLB'S 84-PLCC
Manufacturer
Xilinx Inc
Series
XC5200r
Datasheet
1.XC5206-5PQ208C.pdf
(73 pages)
Specifications of XC5202-6PC84C
Number Of Logic Elements/cells
256
Number Of Labs/clbs
64
Number Of I /o
65
Number Of Gates
3000
Voltage - Supply
4.75 V ~ 5.25 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
84-LCC (J-Lead)
Dc
9629
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Total Ram Bits
-
Other names
122-1131
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XC5202-6PC84C
Manufacturer:
XILINX
Quantity:
1 980
Company:
Part Number:
XC5202-6PC84C
Manufacturer:
XILINX
Quantity:
1 980
Part Number:
XC5202-6PC84C
Manufacturer:
XILINX/赛灵思
Quantity:
20 000
XC5200 Series Field Programmable Gate Arrays
Configuration Sequence
There are four major steps in the XC5200-Series power-up
configuration sequence.
• Power-On Time-Out
• Initialization
• Configuration
• Start-Up
The full process is illustrated in
Power-On Time-Out
An internal power-on reset circuit is triggered when power
is applied. When V
of the FPGA begin to operate (i.e., performs a
write-and-read test of a sample pair of configuration mem-
ory bits), the programmable I/O buffers are 3-stated with
active high-impedance pull-up resistors. A time-out delay
— nominally 4 ms — is initiated to allow the power-supply
voltage to stabilize. For correct operation the power supply
must reach V
not dip below it thereafter.
There is no distinction between master and slave modes
with regard to the time-out delay. Instead, the INIT line is
used to ensure that all daisy-chained devices have com-
pleted initialization. Since XC2000 devices do not have this
signal, extra care must be taken to guarantee proper oper-
ation when daisy-chaining them with XC5200 devices. For
proper operation with XC3000 devices, the RESET signal,
which is used in XC3000 to delay configuration, should be
connected to INIT.
If the time-out delay is insufficient, configuration should be
delayed by holding the INIT pin Low until the power supply
has reached operating levels.
This delay is applied only on power-up. It is not applied
when reconfiguring an FPGA by pulsing the PROGRAM
pin Low. During all three phases — Power-on, Initialization,
and Configuration — DONE is held Low; HDC, LDC, and
INIT are active; DOUT is driven; and all I/O buffers are dis-
abled.
7-108
Figure 23: Circuit for Generating CRC-16
0
1
LAST DATA FRAME
1
X2
1
CC
1
2 3 4 5 6 7 8 9 10 11 12 13 14
1
(min) by the end of the time-out, and must
1 0 15 14 13 12 11 10 9 8 7 6 5
CC
Polynomial: X16 + X15 + X2 + 1
reaches the voltage at which portions
Readback Data Stream
Product Obsolete or Under Obsolescence
CRC – CHECKSUM
Figure
SERIAL DATA IN
24.
X15
X1789
15
X16
Initialization
This phase clears the configuration memory and estab-
lishes the configuration mode.
The configuration memory is cleared at the rate of one
frame per internal clock cycle (nominally 1 MHz). An
open-drain bidirectional signal, INIT, is released when the
configuration memory is completely cleared. The device
then tests for the absence of an external active-low level on
INIT. The mode lines are sampled two internal clock cycles
later (nominally 2 s).
The master device waits an additional 32
(nominally 64-128 s) to provide adequate time for all of the
slave devices to recognize the release of INIT as well. Then
the master device enters the Configuration phase.
Figure 24: Configuration Sequence
(*only when PROGRAM = High)
SAMPLE PRELOAD
SAMPLE/PRELOAD*
SAMPLE/PRELOAD
Boundary Scan
CONFIGURE*
Instructions
CONFIGURE
Available:
EXTEST*
BYPASS
BYPASS
READBACK
BYPASS
EXTEST
USER 1
USER 2
Goes Active after
Master CCLK
50 to 250 s
If Boundary Scan
is Selected
F
One Time-Out Pulse
Completely Clear
November 5, 1998 (Version 5.2)
Data to DOUT
Count Equals
Configuration
Configuration
Configuration
Operational
Data Frame
Mode Lines
Sequence
Generate
Yes
Load One
Yes
Yes
Yes
No
Memory
Start-Up
High? if
Sample
memory
of 4 ms
Config-
Length
Master
Frame
uration
CCLK
Count
V CC
Error
Pass
INIT
Full
3V
Yes
No
No
No
No
~1.3 s per Frame
Pull INIT Low
and Stop
PROGRAM
= Low
Yes
s to 256
X9017
R
s