CY7C64713-56LFXC Cypress Semiconductor Corp, CY7C64713-56LFXC Datasheet - Page 6

• Manufacturer Part Number: CY7C64713-56LFXC
• Description: IC MCU USB EZ FX1 16KB 56VQFN
• Manufacturer: Cypress Semiconductor Corp
• Series: EZ-USB FX1™r

Specifications of CY7C64713-56LFXC

• Applications: USB Microcontroller
• Core Processor: 8051
• Program Memory Type: ROMless
• Controller Series: CY7C647xx
• Ram Size: 16K x 8
• Interface: I²C, USB, USART
• Number Of I /o: 24
• Voltage - Supply: 3.15 V ~ 3.45 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 56-VQFN Exposed Pad, 56-HVQFN, 56-SQFN, 56-DHVQFN
• Data Bus Width: 8 bit
• Data Ram Size: 16 KB
• Interface Type: I2C, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 3
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• For Use With: 428-1681 - KIT USB FX1 DEVELOPMENT BOARD428-1677 - KIT DEVELOPMENT EZ-USB FX2LP428-1339 - KIT LOW SPEED PERSONALITY BOARD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 428-1680; CY7C64713-56LFXC

Note
Table 4. Individual FIFO/GPIF Interrupt Sources
If Autovectoring is enabled (AV4EN = 1 in the INTSETUP
register), the FX1 substitutes its INT4VEC byte. Therefore, if the
high byte (“page”) of a jump-table address is preloaded at
location 0x0054, the automatically inserted INT4VEC byte at
0x0055 directs the jump to the correct address out of the 14
addresses within the page. When the ISR occurs, the FX1
pushes the program counter onto its stack and then jumps to
address 0x0053, where it expects to find a “jump” instruction to
the ISR Interrupt service routine.
Reset and Wakeup
Reset Pin
The input pin, RESET#, resets the FX1 when asserted. This pin
has hysteresis and is active LOW. When a crystal is used with
the CY7C64713, the reset period must allow for the stabilization
Document #: 38-08039 Rev. *F
3. If the external clock is powered at the same time as the CY7C64713 and has a stabilization wait period. It must be added to the 200 μs.
Priority
10
11
12
13
14
1
2
3
4
5
6
7
8
9
RESET#
VCC
INT4VEC Value
AC
8C
9C
80
88
90
94
98
A0
A4
A8
B0
B4
84
T
Power on Reset
RESET
EP2PF
EP4PF
EP6PF
EP8PF
EP2EF
EP4EF
EP6EF
EP8EF
EP2FF
EP4FF
EP6FF
GPIFDONE
GPIFWF
EP8FF
Source
Figure 2. Reset Timing Plots
V
3.3V
3.0V
0V
IL
Endpoint 2 Programmable Flag
Endpoint 4 Programmable Flag
Endpoint 6 Programmable Flag
Endpoint 8 Programmable Flag
Endpoint 2 Empty Flag
Endpoint 4 Empty Flag
Endpoint 6 Empty Flag
Endpoint 8 Empty Flag
Endpoint 2 Full Flag
Endpoint 4 Full Flag
Endpoint 6 Full Flag
Endpoint 8 Full Flag
GPIF Operation Complete
GPIF Waveform
of the crystal and the PLL. This reset period must be approxi-
mately 5 ms after VCC has reached 3.0 Volts. If the crystal input
pin is driven by a clock signal the internal PLL stabilizes in 200
μs after VCC has reached 3.0V
reset condition and a reset applied during operation. A power on
reset is defined as the time a reset is asserted when power is
being applied to the circuit. A powered reset is defined to be
when the FX1 has been previously powered on and operating
and the RESET# pin is asserted.
Cypress provides an application note which describes and
recommends power on reset implementation and is found on the
Cypress web site. While the application note discusses the FX2,
the information provided applies also to the FX1. For more infor-
mation on reset implementation for the FX2 family of products
visit
RESET#
VCC
http://www.cypress.com.
Notes
T
RESET
Powered Reset
[3]
.
Figure 2
CY7C64713
shows a power on
V
3.3V
0V
IL
Page 6 of 55
[+] Feedback