DSPIC30F3011-30I/PT Microchip Technology Inc., DSPIC30F3011-30I/PT Datasheet - Page 164
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
DSPIC30F3011-30I/PT
Manufacturer Part Number
DSPIC30F3011-30I/PT
Description
16 BIT MCU/DSP 44LD 30MIPS 24 KB FLASH
Manufacturer
Microchip Technology Inc.
Type
DSPr
Datasheet
1.DSPIC30F3011-30IPT.pdf
(244 pages)
Specifications of DSPIC30F3011-30I/PT
A/d Inputs
9-Channels, 10-Bit
Cpu Speed
30 MIPS
Eeprom Memory
1K Bytes
Input Output
30
Interface
I2C/SPI/UART, USART
Ios
30
Memory Type
Flash
Number Of Bits
16
Package Type
44-pin TQFP
Programmable Memory
24K Bytes
Ram Size
1K Bytes
Timers
5-16-bit, 2-32-bit
Voltage, Range
2.5-5.5
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F3011-30I/PT
Manufacturer:
MICROCHIP
Quantity:
316
Company:
Part Number:
DSPIC30F3011-30I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F3011-30I/PT
Manufacturer:
MICROCHI
Quantity:
20 000
dsPIC30F
Any interrupt that is individually enabled (using the cor-
responding IE bit) and meets the prevailing priority
level will be able to wake-up the processor. The proces-
sor will process the interrupt and branch to the ISR.
The Sleep status bit in RCON register is set upon
wake-up.
All RESETS will wake-up the processor from Sleep
mode. Any Reset, other than POR, will set the Sleep
status bit. In a POR, the Sleep bit is cleared.
If Watchdog Timer is enabled, then the processor will
wake-up from Sleep mode upon WDT time-out. The
Sleep and WDTO status bits are both set.
21.6.2
In Idle mode, the clock to the CPU is shutdown while
peripherals keep running. Unlike Sleep mode, the clock
source remains active.
Several peripherals have a control bit in each module,
that allows them to operate during Idle.
LPRC fail-safe clock remains active if clock failure
detect is enabled.
The processor wakes up from Idle if at least one of the
following conditions is true:
• on any interrupt that is individually enabled (IE bit
• on any Reset (POR, BOR, MCLR)
• on WDT time-out
Upon wake-up from Idle mode, the clock is re-applied
to the CPU and instruction execution begins immedi-
ately, starting with the instruction following the PWRSAV
instruction.
DS70082G-page 162
Note:
is ‘1’) and meets the required priority level
In spite of various delays applied (T
T
(and PLL) may not be active at the end of
the time-out (e.g., for low frequency crys-
tals. In such cases), if FSCM is enabled,
then the device will detect this as a clock
failure and process the Clock Failure Trap,
the FRC oscillator will be enabled, and the
user will have to re-enable the crystal
oscillator. If FSCM is not enabled, then the
device will simply suspend execution of
code until the clock is stable, and will
remain in Sleep until the oscillator clock
has started.
IDLE MODE
LOCK
and T
PWRT
), the crystal oscillator
POR
Preliminary
,
Any interrupt that is individually enabled (using IE bit)
and meets the prevailing priority level will be able to
wake-up the processor. The processor will process the
interrupt and branch to the ISR. The Idle status bit in
RCON register is set upon wake-up.
Any Reset, other than POR, will set the Idle status bit.
On a POR, the Idle bit is cleared.
If Watchdog Timer is enabled, then the processor will
wake-up from Idle mode upon WDT time-out. The Idle
and WDTO status bits are both set.
Unlike wake-up from Sleep, there are no time delays
involved in wake-up from Idle.
21.7
The configuration bits in each device configuration
register specify some of the device modes and are pro-
grammed by a device programmer, or by using the
In-Circuit Serial Programming™ (ICSP™) feature of
the device. Each device configuration register is a
24-bit register, but only the lower 16 bits of each regis-
ter are used to hold configuration data. There are four
device configuration registers available to the user:
1.
2.
3.
4.
The placement of the configuration bits is automatically
handled when you select the device in your device
programmer. The desired state of the configuration bits
may be specified in the source code (dependent on the
language tool used), or through the programming inter-
face. After the device has been programmed, the appli-
cation software may read the configuration bit values
through the table read instructions. For additional
information,
specifications of the device.
Note:
F
Register
FWDT (0xF80002): Watchdog Timer
Configuration Register
FBORPOR (0xF80004): BOR and POR
Configuration Register
FGS (0xF8000A): General Code Segment
Configuration Register
OSC
Device Configuration Registers
(0xF80000): Oscillator Configuration
If the code protection configuration fuse
bits (FGS<GCP> and FGS<GWRP>)
have been programmed, an erase of the
entire code-protected device is only
possible at voltages V
please
refer
2004 Microchip Technology Inc.
to
DD
the
≥ 4.5V.
programming