PIC16F72-I/SP Microchip Technology Inc., PIC16F72-I/SP Datasheet - Page 40

• Manufacturer Part Number: PIC16F72-I/SP
• Description: 28 PIN, 3.5 KB FLASH, 128 RAM, 22 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F72-I/SP

• A/d Inputs: 5-Channel, 8-Bit
• Cpu Speed: 5 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 22
• Interface: I2C/SPI
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin SPDIP
• Programmable Memory: 3.5K Bytes
• Ram Size: 128 Bytes
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC16F72
8.1
In Capture mode, CCPR1H:CCPR1L captures the
16-bit value of the TMR1 register when an event occurs
on pin RC2/CCP1. An event is defined as:
• Every falling edge
• Every rising edge
• Every 4th rising edge
• Every 16th rising edge
An event is selected by control bits CCP1M3:CCP1M0
(CCP1CON<3:0>). When a capture is made, the inter-
rupt request flag bit CCP1IF (PIR1<2>) is set. It must
be cleared in software. If another capture occurs before
the value in register CCPR1 is read, the old captured
value is overwritten by the new captured value.
8.1.1
In Capture mode, the RC2/CCP1 pin should be
configured as an input by setting the TRISC<2> bit.
FIGURE 8-1:
DS39597B-page 38
RC2/CCP1
Note:
pin
Capture Mode
If the RC2/CCP1 is configured as an out-
put, a write to the port can cause a capture
condition.
CCP PIN CONFIGURATION
edge detect
Q’s
Prescaler
÷ 1, 4, 16
and
CCP1CON<3:0>
Set Flag bit CCP1IF
CAPTURE MODE
OPERATION BLOCK
DIAGRAM
(PIR1<2>)
Capture
Enable
CCPR1H
TMR1H
CCPR1L
TMR1L
8.1.2
Timer1 must be running in Timer mode or Synchro-
nized Counter mode for the CCP module to use the
capture feature. In Asynchronous Counter mode, the
capture operation may not work.
8.1.3
When the Capture mode is changed, a false capture
interrupt may be generated. The user should keep bit
CCP1IE (PIE1<2>) clear to avoid false interrupts and
should clear the flag bit CCP1IF, following any such
change in Operating mode.
8.1.4
There are four prescaler settings, specified by bits
CCP1M3:CCP1M0. Whenever the CCP module is
turned off, or the CCP module is not in Capture mode,
the prescaler counter is cleared. This means that any
RESET will clear the prescaler counter.
Switching from one capture prescaler to another may
generate an interrupt. Also, the prescaler counter will
not be cleared, therefore, the first capture may be from
a non-zero prescaler. Example 8-1 shows the recom-
mended method for switching between capture pres-
calers. This example also clears the prescaler counter
and will not generate the “false” interrupt.
EXAMPLE 8-1:
CLRF
MOVLW
MOVWF
CCP1CON
NEW_CAPT_PS ; Load the W reg with
CCP1CON
TIMER1 MODE SELECTION
SOFTWARE INTERRUPT
CCP PRESCALER
CHANGING BETWEEN
CAPTURE PRESCALERS
 2002 Microchip Technology Inc.
; Turn CCP module off
; the new prescaler
; mode value and CCP ON
; Load CCP1CON with
; this value