PIC16F872-I/SP Microchip Technology Inc., PIC16F872-I/SP Datasheet - Page 68
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
PIC16F872-I/SP
Manufacturer Part Number
PIC16F872-I/SP
Description
28 PIN, 7 KB FLASH, 128 RAM, 22 I/O
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC16F872-ISP.pdf
(168 pages)
Specifications of PIC16F872-I/SP
A/d Inputs
5-Channel, 10-Bit
Cpu Speed
5 MIPS
Eeprom Memory
64 Bytes
Input Output
22
Interface
I2C/SPI
Memory Type
Flash
Number Of Bits
8
Package Type
28-pin SPDIP
Programmable Memory
3.5K Bytes
Ram Size
128 Bytes
Speed
20 MHz
Timers
2-8-bit, 1-16-bit
Voltage, Range
2-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16F872-I/SP
Manufacturer:
PIC
Quantity:
270
Company:
Part Number:
PIC16F872-I/SP
Manufacturer:
PIC
Quantity:
270
Company:
Part Number:
PIC16F872-I/SP
Manufacturer:
SILICON
Quantity:
1 000
Part Number:
PIC16F872-I/SP
Manufacturer:
MIC
Quantity:
20 000
PIC16F872
9.2.10
A Repeated START condition occurs when the RSEN
bit (SSPCON2<1>) is programmed high and the I
module is in the IDLE state. When the RSEN bit is set,
the SCL pin is asserted low. When the SCL pin is sam-
pled low, the baud rate generator is loaded with the
contents of SSPADD<6:0> and begins counting. The
SDA pin is released (brought high) for one baud rate
generator count (T
times out if SDA is sampled high, the SCL pin will be
de-asserted (brought high). When SCL is sampled
high, the baud rate generator is reloaded with the con-
tents of SSPADD<6:0> and begins counting. SDA and
SCL must be sampled high for one T
then followed by assertion of the SDA pin (SDA is low)
for one T
RSEN bit in the SSPCON2 register will be automati-
cally cleared and the baud rate generator will not be
reloaded, leaving the SDA pin held low. As soon as a
START condition is detected on the SDA and SCL pins,
the S bit (SSPSTAT<3>) will be set. The SSPIF bit will
not be set until the baud rate generator has timed out.
FIGURE 9-13:
DS30221C-page 66
Note 1: If RSEN is programmed while any other
2: A bus collision during the Repeated
BRG
I
START CONDITION TIMING
event is in progress, it will not take effect.
2
START condition occurs if:
• SCL goes low before SDA is
• SDA is sampled low when SCL
C MASTER MODE REPEATED
, while SCL is high. Following this, the
goes from low to high.
asserted low. This may indicate that
another master is attempting to
transmit a data "1".
Falling edge of ninth clock
BRG
). When the baud rate generator
REPEAT START CONDITION WAVEFORM
SDA
SCL
End of Xmit
Write to SSPCON2
occurs here.
SDA = 1,
SCL(no change).
BRG
. This action is
2
C
T
SDA = 1,
SCL = 1
BRG
T
BRG
Immediately following the SSPIF bit getting set, the
user may write the SSPBUF with the 7-bit address in
7-bit mode, or the default first address in 10-bit mode.
After the first eight bits are transmitted and an ACK is
received, the user may then transmit an additional eight
bits of address (10-bit mode), or eight bits of data (7-bit
mode).
9.2.10.1
If the user writes the SSPBUF when a Repeated
START sequence is in progress, then WCOL is set and
the contents of the buffer are unchanged (the write
doesn’t occur).
Note:
Sr = Repeated START
T
BRG
At completion of START bit,
hardware clear RSEN bit
Set S (SSPSTAT<3>)
Because queueing of events is not
allowed, writing of the lower 5 bits of
SSPCON2 is disabled until the Repeated
START condition is complete.
and set SSPIF
Write to SSPBUF occurs here
T
WCOL Status Flag
BRG
1st Bit
T
BRG
© 2006 Microchip Technology Inc.