PIC18F6585-I/PT Microchip Technology Inc., PIC18F6585-I/PT Datasheet - Page 351

• Manufacturer Part Number: PIC18F6585-I/PT
• Description: 64 PIN, 48 KB FLASH, 3328 RAM, 52 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F6585-I/PT

• A/d Inputs: 12-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 1024 Bytes
• Input Output: 53
• Interface: CAN/I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 64-pin TQFP
• Programmable Memory: 48K Bytes
• Ram Size: 3.3K Bytes
• Speed: 40 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

REGISTER 24-3:
REGISTER 24-4:
 2004 Microchip Technology Inc.
bit 7-5
bit 4-1
bit 0
bit 7
bit 6-2
bit 1-0
Unimplemented: Read as ‘0’
WDTPS3:WDTPS0: Watchdog Timer Postscaler Select bits
1111 = 1:32768
1110 = 1:16384
1101 = 1:8192
1100 = 1:4096
1011 = 1:2048
1010 = 1:1024
1001 = 1:512
1000 = 1:256
0111 = 1:128
0110 = 1:64
0101 = 1:32
0100 = 1:16
0011 = 1:8
0010 = 1:4
0001 = 1:2
0000 = 1:1
WDTEN: Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled (control is placed on the SWDTEN bit)
bit 7
CONFIG3L: CONFIGURATION REGISTER 3 LOW (BYTE ADDRESS 300004h)
bit 7
WAIT: External Bus Data Wait Enable bit
1 = Wait selections unavailable for table reads and table writes
0 = Wait selections for table reads and table writes are determined by WAIT1:WAIT0 bits
Unimplemented: Read as ‘0’
PM1:PM0: Processor Mode Select bits
11 = Microcontroller mode
10 = Microprocessor mode
01 = Microprocessor with Boot Block mode
00 = Extended Microcontroller mode
CONFIG2H: CONFIGURATION REGISTER 2 HIGH (BYTE ADDRESS 300003h)
Legend:
R = Readable bit
- n = Value when device is unprogrammed
Legend:
R = Readable bit
- n = Value when device is unprogrammed
Note 1: This register is unimplemented for PIC18F6X8X devices; maintain these bits set.
R/P-1
WAIT
U-0
—
(MEMCOM<5:4>)
U-0
—
U-0
—
PIC18F6585/8585/6680/8680
P = Programmable bit
P = Programmable bit
U-0
—
U-0
—
WDTPS3
R/P-1
U-0
—
WDTPS2
R/P-1
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
U = Unimplemented bit, read as ‘0’
u = Unchanged from programmed state
U-0
—
WDTPS1
R/P-1
U-0
—
WDTPS0
R/P-1
PM1
R/P-1
DS30491C-page 349
WDTEN
R/P-1
R/P-1
PM0
(1)
bit 0
bit 0