SCLT3-8BT8 STMicroelectronics, SCLT3-8BT8 Datasheet - Page 27

• Manufacturer Part Number: SCLT3-8BT8
• Description: IC SERIAL TERM 8-LINE 38HTSSOP
• Manufacturer: STMicroelectronics
• Type: Serialr

Specifications of SCLT3-8BT8

• Number Of Terminations: 8
• Voltage - Supply: 9 V ~ 35 V
• Operating Temperature: -25°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 38-TSSOP Exposed Pad, 38-eTSSOP, 38-HTSSOP
• Number Of I/os: 8
• Operating Supply Voltage: 9 V to 35 V
• Supply Current (max): 2.3 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 25 C
• Mounting Style: SMD/SMT
• Data Bus Width: 8 bit, 16 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-10100-5

SCLT3-8BT8
3.5
3.5.1
3.5.2
3.6
Fast transient burst immunity
Considerations on the power section
The EFT protection is achieved with the same strategy as ESD and surge protection. An
input capacitor C
These capacitors play a key role in suppressing front-end electrical stresses. Their
capacitance can be about 22 nF (to validate by test for both EFT and RFI tests).
Detailed considerations for EMC performances, board design precautions and component
selections are also described in ST application notes AN2846 and AN2853.
Considerations on the logic section
The SPI section is not submitted directly to the transient burst disturbance because this
disturbance is applied to the logic input wires and the power supply wires.
Since the power section is protected with the clamping diodes, their serial impedance and
the digital filters, the logic section and the serial interface is protected against the effects of
transients.
Nevertheless, the SPI section may be submitted to indirect effects of the EFT transients. So,
the design of the power supplies (V
board are done with care to minimize the layout influences.
As shown on the suggested opto-transistor schematic on
power supply decoupling capacitors should be added to meet the reinforced immunity level
up ot 2 MHz operation.
Under voltage alarm setting for IEC and device-net
applications
The power supply voltage V
R
For IEC 6131 PLC applications, the alarm /UVA is activated when the power bus voltage is
lower than the activation threshold V
voltage rises above the threshold V
In this application, the resistances are set to R
For device-net applications, the sensor power supply voltage can vary from 11 V to 25 V.
The UVA alarm is set between the lower value and the SCLT minimum operation that is set
at 9 V.
The power supply resistor R
current consumption. The V
diode D
SMAJ30A Transil™ diode are indicated.
TM Transil is a trademark of STMicroelectronics
S
and R
–
–
–
Z
PD
to fit the 1 kV surge requirement. In this case an R
V
V
With V
CON
COFF
:
= V
BG
= (V
I
can be added to meet mainly the IEC 61000-4-6 conducted RFI immunity.
BG
= 1.26 V and V
BG
x (1 + R
+ V
HY
C
CC
C
pin robustness could be increased with an additional clamping
is reduced to match the minimum voltage V
) x (1 + R
Doc ID 15191 Rev 3
S
is monitored by the UVA block through the input resistance
/R
PD
HY
CC
COFF
CON
)
= 0.1 V
and V
S
, 18 V typical.
, 17 V typical, and is released when the power bus
/R
PD
DD
)
S
), the opto-transistors, and the printed circuit
= 1.5 MΩ and R
Figure
C
resistance of 150 Ω and an
Application considerations
PD
13, some R
= 120 kΩ.
CC
C
with the device
network and
27/33