PDI1394L40BEUM ST-Ericsson Inc, PDI1394L40BEUM Datasheet - Page 55

• Manufacturer Part Number: PDI1394L40BEUM
• Description: IC LINK LAYER CTRLR AV 144LQFP
• Manufacturer: ST-Ericsson Inc

Specifications of PDI1394L40BEUM

• Applications: AV,TV, VTR
• Interface: IEEE 1394
• Voltage - Supply: 3 V ~ 3.6 V
• Package / Case: 144-LQFP
• Mounting Type: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: PDI1394L40BE-T; PDI1394L40BE-T

Philips Semiconductors
13.2 AV (Isochronous) Transmitter and Receiver Registers
13.2.1 Isochronous Transmit Packing Control and Status (ITXPKCTL) – Base Address: 0x020
This register allows the user to set up the appropriate AV packets from data entered into the AV interface. The packing and control parameters
(TRDEL, MAXBL, DBS, FN, QPC, and SPH) should never be changed while the transmitter is operating. The only exception to this is the
MAXBL parameter when in MPEG-2 packing mode.
NOTE: When reset of isochronous transmitter is necessary, first disable the transmitter (place bit 4, EN_ITX, LOW), wait for FIFO to empty, then
reset the transmitter (place RST_ITX, bit 0, HIGH). This procedure will ensure that data in the FIFO is transmitted before reset.
Reset Value 0x00000001
Bit 30:
Bit 29..28:
Bit 27..16:
Bit 15..8:
Bit 7:
Bit 6..5:
Bit 4:
Bit 3..2:
Bit 1:
Bit 0:
2000 Dec 15
1394 enhanced AV link layer controller
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
AUDIO mode bit: When = 1, SYT system is in AUDIO mode. When AUDIO = 0 normal SYT time stamping operation is
assumed. With AUDIO = 1, the SYT time stamp for an FSYNC pulse will NOT be appended to an empty bus packet.
Any pending SYT stamp will be held until the next non-empty bus packet is sent. As an FSYNC pulse is input to the
transmitting node’s link chip, an SYT stamp will be made. This SYT stamp will point to a time in the future dictated by
the SYT DELAY value (in register 0x020) added to the current least significant nibble (lsn) of the cycle number, plus
the current cycle offset value. This mode automatically increases SYT_DELAY value by two additional cycles beyond
the value programmed in the SYT_DELAY bits.
TXAP_CLK: Application Clock, default mode, ‘00’ the AVxCLK pin is an input. This pin can become an application
clock for the isochronous Transmitter (and output) by programming it to ‘01’, ‘10’, or ‘11’.
Note that when enabled as ‘01’, ‘10’, or ‘11’, the AV port that is configured as transmitter and enabled will output this
clock signal on its AVxCLK pin.
TRDEL: Transport delay. Value added to cycle timer to produce time stamps. Lower 4 bits add to upper 4 bits of
cycle_offset, (Cycle Timer Register, CYCTM). Remainder adds to cycle_count field.
MAXBL: The (maximum) number of data blocks to be put in a payload.
ENXTMSTP: Enable External time stamp control. Allows an external time stamp (generated by the application) to
be inserted in place of the link-generated time stamp. Defaults to link generated time stamp. The application must
present the first byte of a quadlet-wide time stamp accompanied by the AVSYNC pulse (and AVVALID) to the
AVPORT. The external time stamp quadlet is inputted first, followed by the application data packet. The transmitted
packet size is now one quadlet larger than the original isochronous data packet—Set up the isochronous transmitter
accordingly with SPH = 1. CAUTION: Unless valid IEC 61883 time stamp format (based on the link cycle timer)
is used, the receiving node link chip must be equipped with a time stamp check disabling function similar to the
DIS_TSC bit (register 0x040, Bit 7). Please see section 13.2.8 for details.
SYT_DELAY: Programmable delay of AV1FSYNC and AV2FSYNC. Each cycle is 1 bus cycle, 125 s.
Reset value is “00”, a 3 cycle delay.
EN_ITX: Enable receipt of new application packets and generation of isochronous bus packets in every cycle. This bit
also enables the Link Layer to arbitrate for the transmitter in each subsequent bus cycle. When this bit is disabled (0),
the current packet will be transmitted and then the transmitter will shut down.
PM: packing mode:
EN_FS:enable generation/insertion of SYT stamps (Time Stamps) in CIP header.
Reset Isochronous Transmitter (RST_ITX): causes transmitter to be reset when ‘1’. In order for synchronous reset of
ITX to work properly, an AVxCLK (from either the internal or external source) must be present and ensure that the
reset bit is kept (programmed) HIGH for at least the duration of one AVxCLK period. Failure to do so may cause the
application interface of this module to be improperly reset (or not reset at all). When reset is enabled, all bytes will
be flushed from the FIFO and transmission will cease immediately.
31 30
The programming values are:
00
01
10
11
01 = 2 cycles
00 = 3 cycles
10 = 4 cycles
11 = Reserved
00 = variable sized bus packets, most generic mode.
01 = fixed size bus packets.
10 = MPEG–2 packing mode.
11 = No data, just CIP headers are transmitted.
29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Input
24.576MHz
12.288MHz
6.144MHz
TRDEL
51
MAXBL
PM
SV00886
PDI1394L40
Preliminary specification