PCF8566T NXP Semiconductors, PCF8566T Datasheet - Page 17
![](/photos/39/61/396178/sot158-1_sml.jpg)
PCF8566T
Manufacturer Part Number
PCF8566T
Description
Manufacturer
NXP Semiconductors
Datasheet
1.PCF8566T.pdf
(48 pages)
Specifications of PCF8566T
Operating Supply Voltage (typ)
3.3/5V
Number Of Digits
12
Number Of Segments
96
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Package Type
VSO
Pin Count
40
Mounting
Surface Mount
Power Dissipation
400mW
Frequency (max)
315KHz
Operating Supply Voltage (min)
2.5V
Operating Supply Voltage (max)
6V
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PCF8566T
Manufacturer:
NXPL
Quantity:
1 318
Company:
Part Number:
PCF8566T
Manufacturer:
ALTERA
Quantity:
55
Part Number:
PCF8566T
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
PCF8566T(N371)
Manufacturer:
PHILIPS
Quantity:
185
Company:
Part Number:
PCF8566T/1
Manufacturer:
NXP
Quantity:
4 788
NXP Semiconductors
PCF8566_7
Product data sheet
7.12 Data pointer
When display data is transmitted to the PCF8566 the display bytes received are stored in
the display RAM based on the selected LCD drive mode. An example of a 7-segment
numeric display illustrating the storage order for all drive modes is shown in
The RAM storage organization applies equally to other LCD types.
The following applies to
The addressing mechanism for the display RAM is realized using the data pointer. This
allows the loading of an individual display data byte or a series of display data bytes, into
any location of the display RAM. The sequence commences with the initialization of the
data pointer by the load data pointer command (see
stored starting at the display RAM address indicated by the data pointer (see
Once each byte is stored, the data pointer is automatically incremented based on the
selected LCD configuration.
The contents of the data pointer are incremented as follows:
If an I
Consequently, the data pointer must be rewritten prior to further RAM accesses.
Fig 10. Display RAM bit map showing the direct relationship between display RAM
•
•
•
•
•
•
•
•
Static drive mode: the eight transmitted data bits are placed in row 0 to eight
successive display RAM addresses.
1:2 multiplex drive mode: the eight transmitted data bits are placed in row 0 and 1 to
four successive display RAM addresses.
1:3 multiplex drive mode: the eight transmitted data bits are placed in row 0, 1 and 2 of
three successive addresses, with bit 2 of the third address left unchanged. This last bit
can, if necessary, be controlled by an additional transfer to this address but avoid
overriding adjacent data because always full bytes are transmitted.
1:4 multiplex drive mode: the eight transmitted data bits are placed in row 0, 1, 2 and
3 to two successive display RAM addresses.
In static drive mode by eight.
In 1:2 multiplex drive mode by four.
In 1:3 multiplex drive mode by three.
In 1:4 multiplex drive mode by two.
2
C-bus data access terminates early, the state of the data pointer is unknown.
backplane outputs
display RAM bits
addresses and segment outputs and between bits in a RAM word and backplane
outputs
(rows)/
(BP)
Rev. 07 — 25 February 2009
0
1
2
3
Figure
0
1
11:
2
display RAM addresses (columns)/segment outputs (S)
3
4
Universal LCD driver for low multiplex rates
Table
13). After this, the data byte is
19
20
PCF8566
© NXP B.V. 2009. All rights reserved.
21
22
Figure
mgg389
Figure
23
17 of 48
11.
11).