PCF8566T NXP Semiconductors, PCF8566T Datasheet - Page 20
![](/photos/39/61/396178/sot158-1_sml.jpg)
PCF8566T
Manufacturer Part Number
PCF8566T
Description
Manufacturer
NXP Semiconductors
Datasheet
1.PCF8566T.pdf
(48 pages)
Specifications of PCF8566T
Operating Supply Voltage (typ)
3.3/5V
Number Of Digits
12
Number Of Segments
96
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Package Type
VSO
Pin Count
40
Mounting
Surface Mount
Power Dissipation
400mW
Frequency (max)
315KHz
Operating Supply Voltage (min)
2.5V
Operating Supply Voltage (max)
6V
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PCF8566T
Manufacturer:
NXPL
Quantity:
1 318
Company:
Part Number:
PCF8566T
Manufacturer:
ALTERA
Quantity:
55
Part Number:
PCF8566T
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
PCF8566T(N371)
Manufacturer:
PHILIPS
Quantity:
185
Company:
Part Number:
PCF8566T/1
Manufacturer:
NXP
Quantity:
4 788
NXP Semiconductors
8. Basic architecture
PCF8566_7
Product data sheet
8.1.1 Bit transfer
8.1 Characteristics of the I
Table 7.
An additional feature is for an arbitrary selection of LCD segments to be blinked. This
applies to the static and 1:2 multiplex drive modes and can be implemented without any
communication overheads. Using the output bank selector, the displayed RAM banks are
exchanged with alternate RAM banks at the blinking frequency. This mode can also be
specified by the blink select command.
In the 1:3 and 1:4 multiplex modes, where no alternate RAM bank is available, groups of
LCD segments can be blinked by selectively changing the display RAM data at fixed time
intervals.
If the entire display needs to be blinked at a frequency other than the nominal blinking
frequency, this can be done using the mode set command to set and reset the display
enable bit E at the required rate (see
The I
modules. The two lines are a Serial Data line (SDA) and a Serial Clock Line (SCL). When
connected to the output stages of a device, both lines must be connected to a positive
supply via a pull-up resistor. Data transfer is initiated only when the bus is not busy.
One data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the HIGH period of the clock pulse. Changes in the data line at this time will
be interpreted as a control signal. Bit transfer is illustrated in
Blinking mode
off
1
2
3
Fig 12. Bit transfer
2
C-bus provides bidirectional, two-line communication between different IC or
Blink frequencies
SDA
SCL
Rev. 07 — 25 February 2009
Normal operating
mode ratio
-
f
f
f
blink
blink
blink
=
=
=
2
C-bus
--------------- -
92160
------------------- -
184320
------------------- -
368640
f
f
f
clk
clk
clk
data valid
data line
stable;
Table
Universal LCD driver for low multiplex rates
9).
Power saving mode
ratio
-
f
f
f
change
allowed
of data
blink
blink
blink
=
=
=
--------------- -
15360
--------------- -
30720
--------------- -
61440
f
f
f
elk
clk
clk
Figure
mba607
Blink frequency
blinking off
2 Hz
1 Hz
0.5 Hz
12.
PCF8566
© NXP B.V. 2009. All rights reserved.
20 of 48